Having problems with your 116.2435081 ?
How to remove cover
Repair Help & Product Troubleshooting for 116.2435081
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth
When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums
Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.
Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum
Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.
Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?
... Bissell 8910 ProHeat Clear View Upright Vacuum
Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.
Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums
U6446-900 the drive cable came off and I need to remove the top cover so I can reattach the cable but I can figure out how to remove the cover
From the underside:\015\0121. remove 4 screws holding agitator cover in place\015\0122. remove 2 screws (black screws) holding hose retainer in place, pull hose out through top\015\0123. remove three screws, 2 long, 1 short holding top cover: short ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off
I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums
Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob
The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums
I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!
There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum
Could someone please advise how to remove the cover on a Vax Power Pet 2. I'm trying to change the belt, have removed the screws from the sole plate but the cover seems to be held in place by the
Go here > http://support.vax.co.uk/power-2-upright and download the manual with full instructions ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?
Cover knobs How do you remove the two plastic knobs on the cover for bare or carpet and carpet heighth to get the cover off?
You don't have to remove those knobs to get the cover off. Just 2 screws from the bottom, then on each side you will notice a slot from the bottom, use a screwdriver, insert in the slot, and pry out to release the catches and the top cover will come ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.
That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums
My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?
... Windsor SR12 Sensor Bagged Upright Vacuum
Bissell pro heat carpet cleaner clear cover removal
Just lift it up probably suction holding it ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Removing top cover
To remove the cover you need to gently prise off the rear castors. You will see a couple of grey locking tabs that hold the coloured plastic lid on. Gently prise the two past apart and the lid can be removed. When you remove the lid you may find that ... Vacuums
Dyson slim cannot remove switch cover
Here is video for DC07 switch replacement,http://www.videojug.com/film/how-to-replace-a-dyson-switch-and-actuator-dc07 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How do I remove the bottom cover on powermate #26412690 to replace belt?
... Kenmore Vacuums
I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?
... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?
There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums
I have a bosch ergomaxx 2000w which I need to strip down and clean. Ive found 6 torx screws bit still can't remove the coloured plastic cover. How do I remove it?
Got the same !Remove both back wheels (just pull gently with a screwdriver), then with a big screwdriver pull the cover while pulling plastic locks in the side holes (under the wheels) whith a small screwdriver. ... Bosch Vacuums
I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?
... Panasonic MC-V7515 Bagged Upright Vacuum
Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),
Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o
Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum