Having problems with your Vacuums ?

Install a new 4476 belt

\015 A burning rubber smell tells me my vac ate the belt. I can't open the vac to install a new belt.\015

Answers :

This must be an Eureka vacuum, On the top cover, near the from, are some slots, there is a screw on each side, remove them and the cover will come off. part #54312 U belt. Brush part # is 60252-2 if you need a new one.
What kind of vacuum is it you have? 
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover very noisy after new belt installed.


What is the belt # you have installed (generic)? Yes, there are problems with using generic belts on Hoover Vacuums. If you have noise I would suspect the roller, and replace it. the cost is about $25 and is something that you can install. The newer ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?


Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

My oreck throws off and burns belts. i install a new belt and it runs fine, but as soon as i try to vacuum the carpet, it burns the belt.


... Oreck XL Ultra Bagged Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Install a new 4476 belt


This must be an Eureka vacuum, On the top cover, near the from, are some slots, there is a screw on each side, remove them and the cover will come off. part #54312 U belt. Brush part # is 60252-2 if you need a new one. ... Vacuums

How to instal a new belt for the brush of the bissell ProHeat


Need to install belts ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

New Hoover belt nbr 385280-34 installed, belt still too loose.


There is no adjustment. As they wear they cut the groove in the roller deeper. Sure fix,and what Hoover will tell you to do is to replace the roller. If your like me though that isn't any good. so what I did was wind wax coated dental floss into the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I HAVE A BISSELL MODEL 7920-3 AND IT NEEDS A NEW BELT. I WANT TO KNOW WHERE TO GET A BELT AND HOW TO INSTALL IT. THANK YOU, GARRY


Check here for beltcheck here for how to and belt ... Vacuums

Belt burned up (first time); installed new belt but that starts to burn also; approx. 2 years old


Sounds like the brush that the belt is supposed to turn is bound up tight. Need to remove the brush and clean all debris from it. Where you can get at the center rod for the brush, the rod that the brush spins around, clean the ends and add some WD ... Panasonic Vacuums

Broken belt the belt is broken. how do i install a new one?


... Hoover Soft Light U4266-940 Bagged Upright Vacuum

Dyson dc14 chris do you have a picture the clutch breakdown so i can re assemble my dyson with new belts. you have to take the clutch apart to install belt ,i am having trouble keeping everything alined. thanks


Hi.\015\012\015\012Yes go to http://dysonmanuals.llc.nu/index.htm Then go to contact page then DYSON DISC (4) .\015\012Thi ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vacumm keeps burning up belts i need to make sure the proper way to install new belt


Does it need a real good cleaning\015\012 and make sure nothing in stuck in it ... Panasonic MC-V7398 Upright Vacuum

Change Belt i don't know how to install a new belt on the U4551-920


I couldn't understand the other response so I'll put my two cents worth out there.\015\012\015\012Lower the handle all the way, flip the vacuum over and use a flat screwdriver in the slots as shown to remove the beater bar cover. On the top cov ... Vacuums

Install New Belt


Lift the headlight and rotate the thumb dial to release the carpet head. It will spin to the side. Rotate the square handle at the front of the vac fully to the left. Remove the carpet head and open it from the bottom side. Observe which side h ... Kirby Ultimate G Bagged Upright Vacuum

New Hoover Dimension Supreme vacum belt can't be installed. No


... Hoover U5227-930 Elite Upright Vacuum

I CAN'T SEEM TO INSTALL A NEW UB8 BELT


\015\012\015\012Remove the lower plate \015\012\015\012Carefully lift up on the agitator assembly until it clears both sides of the nozzle housing. ... Panasonic MC-V5745 Bagged Upright Vacuum

How do i install a new belt on a hoover bagless upright


The bottom cover can be removed and then remove beater bar. put belt over beater bar and stretch over motor shaft. ... Hoover U5720-900 WindTunnel Upright Vacuum

I INSTALLED A NEW BELT BUT THE ROTER BRUSH IS STILL NOT TURNING


It's possible that when you replaced the belt, you may have pinch it against part of the vacuum. Or, you may have put the brush in crooked.Jim ... Kenmore Vacuums

I am not sure how o install a new belt on my oreck vacumm, can't


Here is the insturctions (copy and paste in your address bar)http://www.oreck.com/vacuum-cleaner-bags-and-belts/index.cfm?keycode=DB475 ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0855 seconds