Having problems with your Vacuums ?
Vacuum will not turn on
\015 The vacuum cleaner was working fine one minute and then I shut it off. I could never get it to come on again. I can't see any reset button or fuse listed in the parts decription. The switch seems to be working fine (although it could have gone bad I guess) and the power cord seems fine also. Is there a fuse located on this machine (and where is it located) that may have blown?\015
Kenmore Model #216.37000 does it have a reset button. I cleaned the filter and it still will not go on.
Kenmore Model 116, behind the Vacuum cleaner there is a Motor Reset switch which you need to press.
1. Make sure the Vacuum Cleaner is unplugged.
2. Press the reset button gently in with a pen.
3. Plug back the Vacuum cleaner and it should work.
1. Make sure the Vacuum Cleaner is unplugged.
2. Press the reset button gently in with a pen.
3. Plug back the Vacuum cleaner and it should work.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums
The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug
... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.
When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?
... Easy Flo EF2300 Central System Vacuum
I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.
The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
Accidently sucked up a shoelace with the vacuum. I turned off the vacuum and carefully removed the lace. Now, however, the vacuum makes a strange noise when I turn it on and try to vacuum the carpet using the brushes. What can I do?
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan
Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum
Vacuum just turned off when vacuuming and won't turn back on.
If your motor got too hot there is a motorguard switch on there and it has to cool down before it will come back on.check under the vacuum and see if you can turn the brush roller by hand,unplug first.if it turns real freely then the belt is broke.if ... Vacuums
The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.
1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107
No vacuum My Floormate has plenty of air moving, but no vacuum at the nozzle. When I turn it on, the filter hops up to the black rubber "intake", rather than staying in its spot. It seems to me that the intake should be in contact with the filter when the reservoir is installed. And I don't understand why the intake isn't closer to it, but it seems fixed there, almost an inch higher than the filter. When I remove the bottom reservoir and turn the h3000 on, I feel vacuum at the intake, and air
Someone must have lost the filter cover from the machine. It is a clear blue plastic cover that goes over the filter and has a hole that lines up with the motor intake. It is approx. 3 inches square and has an angular top to coincide with the motor i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
The bag light turns on and the vacuum turns off within seconds of turning the vacuum on even with a brand new bag
First try turning dial on top of the machine so the arrow lines up with the smallest dot.\015\012The most likely problem is clogged, worn, or broken control valve assembly (CVA). It could also be clogged tubes to the CVA. This is usually caus ... Electrolux Lux 5500 Canister Vacuum
My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.
... Dyson Vacuums
I was vacuuming with an attachment, the vacuum began to loose suction and the hose collapsed, then the vacuum stopped running. I have turned it off and continue to plug it in off and on, using different plugs. It will not turn back on.
Hi there VacuumGuru for www.vacuumspot.com.au here. You have got yourself a blockage in the hose is all. The reason it wont turn on is because that machine has a thermal cut o ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Rainbow SE I turned the vacuum on and it worked to do one room Then I shut it off to wait until my husband got of his call. I realized that their was cloggage in the vacuum part that vacuums the carpet and unclogged it. I then tried to turn on and it was dead. I have the water filled just above the stick.
The clog may have over heated the motor, usually if you unplug it then after little while, try it again. If it still won't go, does the separator turn easily or is it bound up and won't turn. Take it off and see if the motor will run(without water) ... Rainbow E series Canister Wet/Dry Vacuum
The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.
This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums