Having problems with your Vacuums ?

Electrolux Renaissance Hose Replacement

\015 The hose on my Electrolux Renaissance broke after many years.I found a replacement part on line, but I cannot figure out how to remove the old hose from the handle and connect the handle to the new one (see photo)? Can someone explain how this is done?\015

Answers :

Notice how the hose has a groove just around the outer edge of the gray plastic near the white plastic insert. The hose is held into the handle buy two "tongues" inserted into this groove. One of these tongues is on the end of the top plastic piece of the handle. The second is on the piece of plastic that is slid into the little hole at the base of the handle and it is visible in the picture.

To remove the first, you'll have to remove the two screws in the top of the handle that hold the top plastic piece. This can be a challenge unless you have the right tool. It's essentially a hex-star allen wrench tool that is required, I'm guessing about 1/16 inch. I had one in my tool box that fit. Remove the screws and pop the top plate off. This frees the first tongue from the groove. Now, just get a screw driver (or use your finger) to press the plastic piece inserted in the hole at the bottom of the handle. Press from the "t" side and this should slide right out. Now your hose will slide right out of the handle and you can replace the old with new. Re-insert the small plastic insert, and refasten the top plastic piece of the handle and you're good to go.

-DB
I would bring it to an authorized dealer
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux Renaissance Hose Replacement


Notice how the hose has a groove just around the outer edge of the gray plastic near the white plastic insert. The hose is held into the handle buy two "tongues" inserted into this groove. One of these tongues is on the end of the top plastic piece o ... Vacuums

My electrolux 2100 vacuum hose broke. I replaced the hose but now I dop not have power at the hose end. is there a curcuit breaker in the canister tha supplies power to the hose??


... Electrolux Guardian Bagged Canister Vacuum

How do I replace the handle on Electrolux 1205 powered hose?


... Electrolux Canister Vacuum Cleaner Wand Silverado, 1205

Vacuum hose replace electrolux how to


YOU DON'T SAY IF YOU HAVE THE NEWER HOSE OR THE CLASSIC ONE WITH THE STEEL TIP (BETTER DESIGN). IF IT'S THE LATTER UN-SCREW THE SCREW CLOSEST TO THE STEEL TIP,TAKE A SMALL SCREW DRIVER AND LIFT THE THE PIECE OF PLASTIC THAT WAS SCREWED D ... Electrolux Centralux Vacuum

I have an Electrolux Renaissance Vacuum C104H. How do I get take the hose off of the handle to install a new hose but keep the handle I have?


... Vacuums

Electrolux renaissance power hose


Call 5703261731 ... Electrolux Lux 7000 Bagged Canister Vacuum

Electrolux renaissance hose wiring diagram


... Electrolux Vacuums

My versatility electrolux vacuum is 2 years old and it has lost its suction, i have replaced the filters and checked every hosing area i have access to, it seems to all be clear. I dont know what else to do, it has a higher pitched whinnig sound when it is on


It sounds like the fan blades have worn away until there's basically no air resistance, thus no air flow/suction. The whine is created by the motor turning at a higher speed due to lack of resistance. \015\012The fan wasn't covered by the wa ... Electrolux Vacuums

Electrolux Renaissance power nozzle turning on and off, brass pins hot


The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the i ... Electrolux Guardian Bagged Canister Vacuum

Remove handle hose electrolux renaissance


... Vacuums

How do replace new hose - Electrolux Epic 3500 Vacuum


Manual > http://www.totalvac.com/manuals/electrolux_manual_Epic3500.pdf ... Electrolux Epic 3500 Vacuum

I have lost suction in my versitility electrolux, it has a higher pitched whinning sound, I have replaced the filters and checked all of the hosing, it is all clear


You may want to check and be sure the beater brush is operating properly and that the drive belt has not broken.\015\012The drive belt can brake when the beater brush is frozen up.\015\012\015\012Suggest you remove the beater brush and clean as ... Electrolux EL8502 Versatility Bagless Upright Vacuum

I have a electrolux oxy3 system vacuum cleaner. The floor is damaged, and the hose has been damaged and severed and the copper cables have been cut...so I need to purchase a replacement foot and hose/hand piece. regards Sandy


... Electrolux Vacuums

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?


It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum

I have an Electrolux Renaissance Vacuum C104H. Where can I find buy a hose control handle or the circuit bord for the control handle ?


... Vacuums

I have an electrolux renaissance c104a model vacuum...I got a sock stuck in the hose and took the end of the vacuum where it attaches to the canister apart. There are 4 brass pins that I cannot get back in the correct sequence to operate the vacuum...please help.


... Electrolux Guardian Bagged Canister Vacuum

The plastic 'bracket' for want of a better word has been 'snapped' on either side of the vacuum hose entry point to the head of the vacuum. I have the Electrolux Maximus AMX7025 (made in the EU). Can this part be replaced or do I have to purchase the whole vacuum head?


... Electrolux EL4100 Bagged Canister Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

ELECTROLUX OLYMPIA ONE HOSE


Usually the older hose get replaced, they just weren't made to be repaired, if it looks like something that will come off, then try either warming the sleeve up with hot water or a hair drier to see if you can work it off after it has warmed up. ... Vacuums

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn't thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?


Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in. ... Eureka Sanitaire SC4570 Bagged Upright Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.


Hi\015\012\015\012Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the ... Vacuums

LUX RENAISSANCE WONT TURN ON. HOSE CONTROL BAG LIGHT IS ON


Could be the board in the handle but I found that a lot of the times the contacts where the handle meets the hose just need to be cleaned. It could also be a clogged hose but I'd say it's one of the other two. ... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0460 seconds