Having problems with your Vacuums ?

My Bissell series 65832 vacuum's rotating floor brush is making a really loud noise like its hitting something when ever I turn it on. Can you tell me how I can fix .

Answers :

It probably needs a new belt, unplug the unit and find the screws that hold the cover where the belt it,remove them and look at the belt.Or it could have string or something wrapped around the brushes that would need to be cut out.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell series 65832 vacuum's rotating floor brush is making a really loud noise like its hitting something when ever I turn it on. Can you tell me how I can fix .

It probably needs a new belt, unplug the unit and find the screws that hold the cover where the belt it,remove them and look at the belt.Or it could have string or something wrapped around the brushes that would need to be cut out. ... Vacuums

I have a hotpoint microwave and the turn table does not turn when something heavy is on it. for example it turns if you warm a cup of coffee. is it a belt or the motor slipping? if so, in either case, can i fix it myself? Thanks, ron

Hi,\012Here is a tip that will help you to figure out what is wrong with your Microwave Oven....Microwave ... Vacuums

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!

Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bristles quit rotating and smelled like something was burning. It isn't the belt that turns the bristles. Can't afford a repairman, can you help me fix it?

Belt can reamin intact but still jam and burn. It won't necessarily break. I suggest you remove the bottom of the vacuum where the bristles spins and where the belt is located. You may have something jammed in there. You may need to remove the bristl ... Bissell 6594 PowerForce Bagless Upright Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.

Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No power is coming in. plugged in, will not turn on. last time i used it, it would go on/off. if i bumped or hit it, it would turn back on. can this be fixed by a fair novice, or trash it?

Sounds like a loose wire or contact of some sort.\015\012Might be a bit too much for a novice to tackle.\015\012\015\012I would start by UNPLUGGING the unit and try to get at the ON/OFF switch to see if there is a wire loose. If no loose wire ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of

Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Goes slightly forward and then backs, turns and tries again. As though it is hitting something in front of it

Take a can of air with the attachable tube and blow it into the underside near where the guard attaches. If you move this back and forth you will see some pivots underneat the the device. These pivots block the electronic eyes, which are clouded wi ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Hi...everytime I turn on my vacuum it blows out a bunch of dirt/dust...the belt seems to be intact...what can the problem be? Is it something i can fix myself possibly?

This is most likely a clogged inlet, clogged hose, or a clogged filter. Just need to inspect it thoroughly and give it a good cleaning.\015\012\015\012More info, let me know.\015\012\015\012Charlie ... Dirt Devil M085850 Featherlite Bagless Upright VacuumVacuum

Kenmore 23613 The vacuum when turned on has a burnt smell. My husband has taken the vacuum apart, still can't seem to get to the belt. The belt in the rug part is not the problem, it is something in the canister part. Can you tell me what you think might be our problem? Thanks!

If it smells like burnt plastic it is something wrong with the motor part, but if it is a wet dog,burnt hair gross kinda smell it cool change the bag and buy deoderizer tablet to put under bag kinda like a airfreshener. if it dont work like it used ... Kenmore 22085 Bagged Canister Vacuum

The brushes on my dyson cleaner won'tn turn. Can you help and tell me how to fix this please.

Probably jammed with hair or fibre most commonly. The base comes off by means of a 1/2 turn anti clockwise of 3 'screws' on the base and the base clips off and on. Recommended you do this each time you use the cleaner. Alternately it may be a broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I by accident sucked up the corner of a sheet into the powermate of my vacuum. I turned the vacuum off and pulled out the sheet but now the powermate is no longer working (suction works fine) Is this something I can fix on my own?

These power heads have a kill switch on them. Not exactly clearly labeled. the kill switch reset button should be on the right side of the unit as you look down like you are using it. you may want to try pushing it with the power to the p ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hi i have a dirt devil reaction fresh vacuum and after a few minutes it shuts off and i have to wait an hour before it will turn on again is there a recall on this model or is there something i can do to fix it?

I traded it in for a bagged vacuum thanks though ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Lift-Off Bagless Deluxe model number 3750L hi there, can u please tell me if there is anyway i can fix my brush roll; It is not turning and the rubber band is getting burnt out; More

Hi\015\012You would need to replace the brush module. You can contact Bissell customer service here at this link I'm giving you and they can direct you to a local dealer that will have what you need. ... Vacuums

The brush does not turn but the belt seems very tight. There is also suction at the top of the hose but no suction at the brush head. I have removed ever pat that I can tell that comes off. Any suggestions?

DC07s have two drive ... Dyson DC07 Bagless Upright Cyclonic Vacuum


When the vaccum is upright, the beater bar is not engaged. When you tilt the handle back, the clutch engages and the beater bar begins to turn.\015\012\015\012There are two likely possibilities for the "screaming noise". First, and most l ... Dyson Vacuums

Hi there, can u please tell me if there is anyway i can fix my brush roll; It is not turning and the rubber band is getting burnt out;

Can you tell me the brand and model number of your vacuum? I will check if there's a way to fix it.Thank you! ... Bissell Vacuums

I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?

The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.

I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

I have a Dyson DC14..I was vacuming and when I stopped the vacum would not stand up..it wouldn't click in the stationary poistion. When I turned it on all the suction is coming from the hose even though it is tilted. Can I do something to fix this?

Yes! Stand behind the machine. Hold the handle at about 45 degree angle. Remove the airway inspection valve (press the yellow release button that's between the right wheel and the clear bin and then just pull away that curved piece of plastic pipe). ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I'm not really a technician, but I used to sell Filter Queens and was taught how to maintain them, and have tackled "fixing" some problems. I am a 71 year old great-grandmother of 8, but have good health and am very active. The Filter Queen I have is r, usedeally old, and I have kept it up. Just this week, however, I turned it on and it had a noise which sounds like something might be loose in the motor. I have always been very careful to have a clean hepa filter to protect the motor, so I know

It's tricky to hold screws with one hand and screwdriver with other hand; however, I am 65-yr-old female and do it yearly with 100% perfection! Take a break, relax, and try again! I sit on floor, put attachment between legs for supporting vacuum, h ... Filter Queen Majestic Canister Vacuum

I was vacuuming today, and it was doing fine, then all of a sudden the motor kicked up a notch or two, then I heard the LOUDEST POP!!!...I turned it off, went and unplugged it, took off the top of the canister, then took the water pan to empty it, because I seen something on the bottom, as I was pouring the water out, I seen on the bottom, ALOT of, what looked like, small bands of metal...could you tell me what may have happened..??

It's possible the fan on the motor has disintgrated. If this is the case replace the motor. ... Rainbow E series Canister Wet/Dry Vacuum

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?

... Rainbow E series Canister Wet/Dry Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0538 seconds