Having problems with your Vacuums ?

Polti AS807 Lecologico switch-on problem

\015 Sometimes, any attempt of switching on the cleaner (button on integrated control at the beginning of the stainless stell telescopic tube) does not have any effect... \015\012Is it any heating protection mechanism?\015\012However, I also have the problem when the cleaner is cold...\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Polti AS807 Lecologico switch-on problem


... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

My vacuum cleaner will not shut off when turned on. I have had it serviced twice by Sears, and for the third time I have experienced the same problem. I disassembled the upper have and it appears that the plastic mechanism designed to turn the switch on and off does not always catch the switch. Is there a way to fix this problem.


Put in a new switch, like toggle switch or use one off an old junk vaccum ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-


Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b


WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?


Go to this website\015\012and enter your complete model number in the search field in the upper\015\012right corner of the page. You should be able ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Brissel Healthy Home Hepa Vacuum: On/Off Switch works sporadically. Took handle apart and the switch worked for a while. I am wondering if I need to replace the switch? Also the Brush Switch is having similar problems.


Might not be the switch there is a connection on the swivel by the base that likes to fail ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?


Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

Dash controls will not switch from normal to defrost or bilevel. buttons light up but no change. 1993 Buick regal. Problem began as no switching during accelleration but would then switch when the engine wasn't pulling the vacuum


Hello this sounds like a vacuum issue to me.The tiny vacuum hose going to heater system is either split or came off there is also a check valve on this vacuum circuit.that could have gone bad.Also the vacuum ball might have a crack in it.But with out ... Vacuums

I have a ge light switch receiver rf1023, with incandescent bulbs, and when I try to switch it on it just blinks once and goes out. if I hold the switch on the battery-operated wall remote, the lights keep blinking until I let go. It used to work fine, and now it doesn't. I've lost the intallation instructions, so I don't know if there was a trouble-shooting section that covered the problem.


... GE Vacuums

I have a Kirby G4 it will start with the hose attachment but not the vaccum housing attachment ? I'm guessing a problem w/ the switch ....when I look at the switch I see two buttons I can actually


Check this vieo out these are safty switches ... Kirby G4 Bagged Upright Vacuum

Carpet/Floor Switch problem on Hoover WindTunnel Vacuum


Well, you have to deal with it, you have to play with this electrical things if you want to fix this problems.\015\012\015\012The good news is, the sources of the problems is the switch already\015\012broken.The first things before you do ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Polti Vaporetto 2400


The first problem you'll have is to unscrew the case. You will need a Torx security key -I bought a set from toolspot.co.uk Code PR7424 Toolzone 9pc Security Torx Keys. This unscrews the case. (I think I paid around £7 incl delivery) The probl ... Vacuums

The switch on and off wont work so i took it off and it works but know iam having problems putting it back together the spring are the problem


Those springs are tricky to get back in. you can use the flat end of a screwdriver to hold them down and compress them. I would recomend taking it to a proffesional to get it put back together right before you break the plastic and cost yourself some ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The switch on the wall only works to control the fan and not the light- it won't turn off the ligght. I replaced the switch but it did not solve the problem


If this is a new installation and there was only one switch on the wall, say to control a light that was once there, then you have that switch hooked up only to the fan.\015\012If you want to control the light as well, it has to be wired up at the bo ... Vacuums

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.


The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks


This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

Brush not spinning , no belt is needing to be replaced, i think something in switch, cause before this problem the switch was always on , i would plug/unplug to turn it on. thisis case with 2 vacuums i have


... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?


Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Will not turn on when I hit on switch. I have checked safety switch where head attaches but it doesn't seem to be a problem there.


Check fuse in the plug or better still if you have and can use multimeter check voltage present @ switch ... Kirby Ultimate G Bagged Upright Vacuum

Horrible noise The same problem that has been the other people have experienced, I can make the noise stop if I switch to floors, but it doesn't work well on carpets. Has anyone been able to fix this problem?


It sounds like you have a blockage. Go to this at Dyson to look at your item in more detail. They have good support here for your item. Just copy and paste into your browser.http://www.dyson.com/support/help.asp?product=DC17-ANIMAL&ar ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?


It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0467 seconds