Having problems with your Vacuums ?

Replacing Compact Power Neck on Tri Star Vaccuum Cleaner

\015 I can't figure out how to disassemble the two parts on the power head of my Tri Star DXL vaccum cleaner to replace the Compact Power Neck. I can not find the orriginal invoice but I know it is over 10 years old. If ther is a repair manual you an send to my e-mail it would help.\015

Answers :

Remove the hose from the front cover and pull the electric cord out 2 or 3 feet. Remove the paper bag. Place the vacuum upside down on a work bench with some kind of pad underneath. Open the bag door and pull the end of the soft pastic rail cover out slightly (on both sides) to expose the rigid plastic side rails underneath. If you look directly at the side rails from the front you will see that the ‘T’ shaped part of each rail slides into a channel that locks the top and bottom halves of the machine together. The rails have notches or barbs on the last half inch or so which keep the rails from sliding out. You will need to get these notches away from the channel by sliding a narrow flat blade screw driver in between the top of the ‘T’ and the channel. Just tap it in and leave it there while you pull the rails out with a pair of needle nose pliers. Next, take a look at the bag door hinges. They have a square hole in the center through which a small tab from the bag compartment pokes through. Take a larger flat blade screwdriver and carefully pry the edge of the hinge away from the tab. This will release the bottom section (which is really on top now of course). If you remembered to pull out the two or three feet of cord before you started then you should now have enough slack so that you can lay the bottom section aside.
If you plan to do any electrical work be sure to mark the locations of the wire connections.
\015\012
\015\012try this.
\015\012thanks
\015\012keep updated.
Hi to disassemble the vacuum cleaner you will need specialized tools, you will have to get it relaced by a technician
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing Compact Power Neck on Tri Star Vaccuum Cleaner


Remove the hose from the front cover and pull the electric cord out 2 or 3 feet. Remove the paper bag. Place the vacuum upside down on a work bench with some kind of pad underneath. Open the bag door and pull the end of the soft pastic rail cover out ... Vacuums

A family member recently gave me their Kenmore Vacuum Cleaner (model 35821) and I did not notice that the power cord was missing at first. I tried to look closely at the manual online to see if this was something I would be able to purchase or if the vacuum was no longer any good. Do you happen to know if there is a replacement part for the actual power cord for this item?


Any power cord 17 gauge or lower will work ... Vacuums

I'm trying to replace the power cord on my Hoover Telios vacuum cleaner. I have the machine open on the floor, but can't work out how to find the terminals on the cord rewind reel - they seem


... Hoover Telios Canister Vac Vacuum

I have just purchased a new Nilfisk vaccuum cleaner 150 extreme and used it for 5 minutes and switched it offf. When I tried to restart the machine it would not start. I cannotg et it to restart-how to i solve the problem -the power light is on


If you're just purchased it I suggest you need to check where your local Warranty Agent is and take it there for a service. Since this model has an electronic switch (do the lights flash on and the middle one stays green when powered on at the power ... Vacuums

Replace power lead on panasonic vacuum cleaner MCE 468


Generally, there are 'hidden' screws which are found under plastic plugs. Look for them. You may also find some screws on the opposite side of the plate holding the lead. Finally, sometimes the plate will slide up or down from its fixed position. ... Vacuums

Trying to find a manual to replace power bush belt


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

Miele Champagne Vacuum Cleaner Model S548 I was using the vacuum as normal, moved locations so I plugged into another outlet & suddenly there was no power to the vacuum! I tried it in several other outlets, tried the reset button... & still no power to the vacuum. Any ideas what could be causing this? Any info would be greatly appreciated. Thank you!


Greetings from ,\015\012 \015\012This definitely sound like a cord reel issue to me. This is really the only problem that I ever see on a Miele vacuum cleaner. 9 times out of 10 the cord reel needs to be changed. If you purcha ... Miele Blue Moon Bagged Canister Vacuum

Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch


... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Dyson dc05stduk vacum cleaner need to replace power cable


Hi \015\012\015\012Try this site does manuals on Dc05 repairs.\015\012\015\012http://dysonmanuals.llc.nu ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

We own an ElecktaPure Exclusive Edition EP-4000 cannister vacuum cleaner and we are having a heck of a time trying to find replacement bags for it. We could not find the original part number of a suitable replacement part number. Can you help?


... ElektraPure Vacuums

Polti 2400 I am trying to remove the casing from the steam cleaner to fit a replacement wheel. The screws holding the casing are similar to torx but they have a raised centre which means they can't accommodate a torx screwdriver. I thought this was going to be easy just replacing a snap-in wheel!


You can buy T15 torx driver with hole in them from link below. ... Polti Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I'm trying to remove the power switch assembly for my Dyson DC25 so I can replace the power cable. I took out the 3 screws with a T15 screwdriver and released the top two retainter pins, but the lower half of the assmbly won't detach. Please help!


Replace the two bottom screws but don't tighten up just a few turns in will do, then using the screwdriver push firmly each screw and this will release the lower part of the cover hope this helps. ... Vacuums

Hello,I have iRobot Rooomba Discovery 4200 about 2 years,but I didn't use it about 1 year.Now I tried to use it again,but doesn't work.I charged it 16hours,the power was green,but after leaving home base again red lihgt on power and stopped to work.Do you think that I need to replace battery?Thank you


The Roomba's batteries are made to be in constant use. It is more likely that the battery cells are dried up. You will need to replace the battery. ... iRobot Roomba 4210 Bagless Robotic Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power Switch How do I get the power switch out to replace it? I have a D4C model. Rainbow/Rexair. Is there a place where I can get a parts breakdown of the vacuum cleaner? Steve


This is not that hard:1. - remove gasket (it is glued so you may end up damaging it)2. - remove 4 screws holding baffle 3. - under it yo ... Rainbow E series Canister Wet/Dry Vacuum

I need instructions to replace a diverter door on a Bissell 1698 Power Steamer Proheat carpet cleaner. I already have the replacement part


Hi,Download the Service Guide that would have all the information :-http://www.managemyhome.com/mmh/lis_pdf/OWNM/99040364.pdfHope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Vacuums

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

Eureka model 7605 type A - 'the boss' lite. would not power on yesterday. working perfectly before. i replaced full bag with clean bag this morning. still won't power on. is there a reset button, or anything else i can try? Thank You!


... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0787 seconds