Having problems with your Vacuums ?
Vaccuum Burnout? Is there a reset button on the Infinity Shark Vaccuum? The vaccuum got plugged with a dryer sheet and the motor may be burned out but I'm not sure at this point.
Can anyone suggest what to do?
email: [email protected]
Will the brush turn by hand ok, or is it froze up, some models have a reset on the back near the bottom, there could be a fuse, take the bag door off, near the top of the vacuum, there maty be a cover to remove, if there is a fuse it would be in there. The motor protector may be bad as well as the motor. Your vacuum will just have to checked over to find the problem.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vaccuum Burnout? Is there a reset button on the Infinity Shark Vaccuum? The vaccuum got plugged with a dryer sheet and the motor may be burned out but I'm not sure at this point. Can anyone suggest what to do? Cheers, Vince email: [email protected]
Will the brush turn by hand ok, or is it froze up, some models have a reset on the back near the bottom, there could be a fuse, take the bag door off, near the top of the vacuum, there maty be a cover to remove, if there is a fuse it would be in the ... Vacuums
HA-871? I'm not sure if anyone can help with this, but I've got a **** Smith brand HA-871 alarm system which I haven't used in years. When trying to get it working, not only have I forgotten the code but I can't remember how to enter it (as in, 4 digits and a #, or just the 4 digits, or something else...?). As I am able to get into the alarm box with the key, does anyone know how to reset it and enter the code? I can't find the manual either. Thanks to anyone able to help with this!
Incase you are still interested you set the code with the four jumpers inside the unit.\015\0121st digit is the brown wire\015\0122nd digit is red wire\015\0123rd digit is orange\015\0124th digit is yellow ... Vacuums
No Suction The suction of the vaccuum has stopped. We haven't had the vaccuum for very long and the bag has been recently changed. Both the floor vaccuum and the hose are not picking anything up. I'm not sure what the problem could be.
Your Power head is blocked with hair or dirt,,or the hose which connects the Upright with the power head is blocked.Try taking a steel coat hanger apart (straighten it out) and then push it into the pickup hose to remove blockage. ... Eureka Smartvac 4870 Bagged Upright Vacuum
Shark rotator the lights and stuff still turn on but the vaccuum will not suck. If the lights didnt turn on i would just think the vaccuum quit working all together. ive emptied it, cleaned the filter and made sure theres nothing clogging it.
Took my vaccuum in for service recently and not sure I got my vaccuum back. Doesn't work very good and looks a little different to me. Trying to verify the serial number to compare to my records....is it the bar code number on the bottom?
The serial number for all "G" models, containing 10 digits, is located on the side of the machine above the hole the bag attaches to. ... Kirby Ultimate G Bagged Upright Vacuum
Does anyone have a wiring diagram for bissell upright vaccuum?
What is the exact model number of the unit.please mention it.so the exact wiring diagram can be provided if possible.\015\012check out.keep updated.thanks. ... Bissell Vacuums
I was lucky enough to get a Janome 372 very cheaply at a second-hand store but it came without the manual. A friend managed to thread it so that it works but the threading is completely counter-intuitive and I'm not sure that I'll be able to remember how to do it without a threading diagram to turn to in a pinch. Unfortunately, I can't seem to find a threading diagram online anywhere! Can anyone direct me to a site that shows this?
I would look in a site called www.Pronto.com/manualsI hope this is helpful to you . ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Vaccuum is not picking up. We have cleaned it and looked at the underneath to make sure nothing is stuck -- still not picking up -- just kind of moving stuff around on the floor
... Dyson Telescope Reach All Floors Vacuum
Make a very loud noise when I try to vaccuum the carpet. It sounds like it's something in the brush up front. Belts look good and obstructions are gone. Not sure what else to do.
\015\012Try to lower your wheels a bit which will raise your vacuum a little off the ground. When you vacuum a bare floor you want the vacuum as close to the floor as possible. When you vacuum a carpet if you don't r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My vaccuum cleaner is an EVERSTAR 1200. I turned it on - everything appears OK until I realize that it is not suctionning. I cleaned out the canister - made sure the vacuum was not obstructed. Still no suction. What could it be?
First clean the filter on top of the canister, do not wet it, blow it and get all the accumulated dust out. Then check the hoses for obstruction. There should be an emergency valve on the rear part, if it is open, you better ck the hoses. ... Vacuums
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
Replaced the pump and solenoid on my Bissell Proheat, model 9200 H, but not sure I got the tubing connected back right. Can anyone help me with this?
... Bissell 9200 Upright Vacuum
My Vaccuum Hoover U5763-900 wind tunnel Twin Chamber is barely used. Belt is in tact and agitator is not worn. Nothing clogged. Agitator spins fine off the ground or on hard surface or flat rug. Once on carpet, the agitator won't spin. Not sure why. I have taken it apart over and over again.
... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My Vaccuum is barely used. Belt is in tact and agitator is not worn. Nothing clogged. Agitator spins fine off the ground or on hard surface or flat rug. Once on carpet, the agitator won't spin. Not sure why. I have taken it apart over and over again.
Vacuum height is set too low, jamming the brush ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
I need a manual for a Dirt Devil Vision Easy Steamer MCE7350 im not to sure if our carpet cleaner is broken or we just dont remember how to use it! if anyone can help me out thanks!
You can get the manual on the link below.\015\012\015\012http://static.highspeedbackbone.net/pdf/Dirt-Devil_MCE7350_Manual.pdf ... Dirt Devil MCE7350 Vision Easy Steamer Bagless Upright Vacuum
I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?
... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
I have a DC04 which is a number of years old and has started making an awful grinding sound, I'm sure it is the belt which I sprayed with WD40 and this helped for a couple of seconds but as soon as I recline the hoover it makes this noise but not when upright and using the hose. Does anyone have any ideas or how to change the belt? Thanks
You have to change the belt look it up with your local vacuum store. ... Vacuums
HI! i am not sure what the part is called that i need for my DC07. I can point it out on the vacuum. i think it is a hose that connects the bottom part of the vaccuum to the bucket part...i am sorry that i am not more specific.
It is called an "AI VALVE" - it looks like a Tuba and has two buttons that you push to take it off the machine - it sits into the square hole above the wheel and connects to the round hole next to the dirt bin. Call the Dyson helpline to order the pa ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I don't have instructions for the Rainbow shampooer. I'm not sure how much water to put in, or whether I put water in both reservoirs. Does anyone know?
Water only goes into the cub in the handle. The dirty water gets put into the bowl on the canister part. ... Rainbow Vacuums
The hose on my vaccuum is not picking up. I am pretty sure something is blocking the hose up but not all the way. Is there a way that it detaches from the vaccum and if there is what next?
The hose should be attacthed by two screws or two clips, depending on the model BISSELL vacuum you have. \012Remove the hose and push a broom handle through the hose to clear the clog. ... Bissell Vacuums
Hi I have an Electrolux Envirosteamer and it has stopped steaming. I have made sure the water cap is on tight and also taken the head apart (where the hose finishes up and the attachments fit on) and the hose is intact there. I have no steam and wonder if I have a valve problem? if so can anyone tell me if it's worth trying to order the part and fix myself. I'm fairly handy! Thanks Sue
If the water is boiling and element is ok then it could be the outlet valve it is poss to diy but is a 2 person job as very fiddley ... Eureka Deluxe Enviro Steamer Vacuum
Dry/Wet vac is blowing instead of vaccuum
Check to see if the plastic ball is stuck . There should be a ball under the motor , make sure it moves freely. Make sure your vacum lines are not plugged . Best of luck Ed. ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum
Eureka 4337 BH vaccuum - when I connect attachments there is no
... Eureka 4337BTH Vacuum
My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385
... Kenmore Vacuums
On my M&S Air Vac AV425 central vaccuum system, the system usually turns on by inserting the vaccuum hose into one of the vaccuum outlets. However, it now runs continuously. I am able to turn it off only by unplugging the vaccuum from the electrical outlet. I would like to know how to trouble shoot the problem or how to find someone who services Air Vac systems in the Bridgewater, New jersey area.
We are a central vacuum service company and we service all of new jersey. sounds like you have a short some where that keeps your unit running or it could be your relay module thats stuck our number is 908-721-7595 its j&j central vacuum services ... Vacuums