Having problems with your Vacuums ?

Change Belt i don't know how to install a new belt on the U4551-920


Answers :

I couldn't understand the other response so I'll put my two cents worth out there.\015\012
\015\012Lower the handle all the way, flip the vacuum over and use a flat screwdriver in the slots as shown to remove the beater bar cover. On the top cover pry off the height adjustment slider.   With the screw driver pry along the underside of the top cover.  You'll see four points where the underside of the cover hooks over a mating point on the bottom chassis.  The top of the vacuum will practically fall off once you've dislodged the hooking points.  From there is easy to see how to change the belt by taking it off the motor armature and pulling out the beater bar and belt.  Reassemble the same way.  The cover goes on almost automatically and clips in place.  Put the height adjustment slider back on and snap the beater bar cover back in place.  That's it.  Cheers
Turn the vac. over, remove the bottom plate covering the brush roll, then on the bottom of the top cover, on each side there should be 2 slots when you can put a flat blade scredriver, pry up to release the tabs holding the cover on. The know will come off also when you do this, just put it back on when the put the cover back on. Put the belt on the brush roll and feed it thru the opening and stretch to put over the motor shaft. The top cover, push down to lock it.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change Belt i don't know how to install a new belt on the U4551-920


I couldn't understand the other response so I'll put my two cents worth out there.\015\012\015\012Lower the handle all the way, flip the vacuum over and use a flat screwdriver in the slots as shown to remove the beater bar cover. On the top cov ... Vacuums

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it


Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

My belt broke. I have a replacement. I dont know how to install the replacement belt.


There's a plastic cover over the agitator. (the part that should spin, with tough bristles)Unscrew it. Pull out the agitator. Put the new belt over the 'spinner' (the part that's connected to the motor) and the special pafrt of the agitator. Sn ... Vacuums

I HAVE A BISSELL MODEL 7920-3 AND IT NEEDS A NEW BELT. I WANT TO KNOW WHERE TO GET A BELT AND HOW TO INSTALL IT. THANK YOU, GARRY


Check here for beltcheck here for how to and belt ... Vacuums

I bought a new Bush MP2200BUK 2GB MP3 Player today and havent a clue how to download music from my laptop to my mp3 player and donw know if i have installed it right nothing is happening and dont know if i can download music from my frostwire (music download)


Does anybody know where i can get a new front cover for my 8gb bush mp3 player ... Vacuums

DONT KNOW HOW TO CHANGE MY BELT


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=698891\015\012Generic problem for all Vacuums\015\012DONT KNOW HOW TO CHANGE MY BELT\015\012Posted by m ... Vacuums

Dont know how to change the belt on a 1697 bissel powersteamer pro


There is a great video on the Bissell site. 1 min watching it shows you how.Basically you unplug it, take out the tanks, turn it upside down, remove the 2 red clips that hold the brush assembly, and lift the assy out, then replace belts. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Dont know how to change belt on bissell pro heat carpet steamer cleaner


See thishttp://cache.vendaria.com/vpop/VpopV6.html?ct=13&ctname=CT630X556D630X390&fw=630&fh=556&logo=49&fv=10&ap=vnd_bissell_deap_cleaner_how_to&purl=MAIN_bissell_how_to_replace_upright_deep_cleaner_belts&i ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Have new oreck quest canister and having trouble figuring out how to change vacuum bag. I have the plastic piece that you attach bag to, but don't know where the piece fits into the vacuum. looking for a diagram or manual to see where to install the plastic piece


... Oreck Vacuums

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

I need to change the belt on my Bissell Pro heat. I dont know how to get to it!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have acquired a second hand amway CMS2000 it needs a new belt by the lookds of it but i dont know what this vac can really do is it a carpet cleaner as well and what are the products and how do i clean with it.


... Vacuums

I have a hitachi 1300 upright hoover and dont know how to change sdrive belt


... Hitachi Vacuums

I dont know how to change the belt on my hoover turbopower 4000


... Hoover U5264-930 TurboPower Bagged Upright Vacuum

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

Changing belt Please advise how to change the belt. I wasn't the person who took the belt off, didn't watch. Now it's just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn't have in the right spot! don't want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680


Step 1: Lower handle to floor to change belt Step 2: Remove the two screws from the top hood on the footStep 3: Lift hood to remove Step 4: Lift right end of brushroll (the belt end) Step 5: Remove and discard belt.Step ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0956 seconds