Having problems with your Vacuums ?

Need to install a new power switch

\015 Actually I bought a used vax vaccuum as the switch was not working i bought a switch when i open the the vacuum to my surprise the wiring from the old switch is been removed and by passed.\015\012\015\012My problem is to figur out the wires and which terminal it goes in the switch. the switch (CHILY 7021) got 4 terminals numbered 1, 2, 4, 5.\015\012no.3 and 6 are empty.\015\012\015\012Thanking you.\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to install a new power switch

... Vacuums

The Intelliclean function isn't working properly. The indicators illuminate when I switch Intelliclean off, then on again, but the indicators are not changing (nor the power level) when I vacuum dirty areas. I need to install new filters, could a dirty sensor be the problem?

I was having the same problem with my Intelliclean and I read somewhere on the internet that I should undo the bag, clean in the area where the bag attached to vacuum. When I took bag off, something was stuck there and after I removed it, everything ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

I need to install part #PHP-236/C45ECUE. This is the connector in the top of the wand that connects the power to the brushes near the thumb switch at the end of the flexible hose. (Hope this makes sen

... Kenmore 22812 Bagged Canister Vacuum

Purchased a new, portable, vacuum this date. 4/24/08 at Gottschalk's. Got it home, unpacked it and installed attachments. plugged into a power source, and depressed the power switch, machine did not come on, used three different power sources to no avail. advise--- Reply to [email protected] asap

Being under warranty, I would take it back for an exchange. You don't want something brand new and it is dead on arrival. Either that or take it to a warranty shop for repair. You mess with it and that avoids the warranty. ... Vacuums

Eureka bagless model 5893 Need to know which wires go where when installiing a new on/off switch. One wire is black and the other 2 are purple and blue.

... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

I have a galaxy GL-100 power unit, need to install new motor brush-how to I access them

... Galaxy Vacuums

I need to install a new power cable, please help

Have a look at www.dysonmedic.com. They have some great info on how to dismantle and repair a DC07. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Rainbow mod. D4C have new on /off switch, 2 black, 2 blue wires. need to connect power cord, motor and carpet sweeper?

Are the wires still attached to the old switch? If they are, hook them up to the new switch in the same, physical way. If they aren't attached, you might take it into a vacuum repair shop- they could probably help you figure it out, if you bought ... Rainbow Technologies D4 Bagless Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.

You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

What's your problem?I have to replace the power switch on my Hoover U6485-900. What part do I need to orer? Wher can I order it?

... Hoover U6485900 Bagged Upright Vacuum

Eureka Vacuum Excalibur Model 6975A on/off switch won't turn off. Probably need new switch but can't figure out how to get cover off to get at switch

... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available

Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?

... Vacuums

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?

You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

My samsung quiet storm modl 9068G needs a new brush in the power head. Where can I get one?

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a Dirt Devil rechargable stick vac that has lost power. Does it need a new battery and if so, where can I get one and how much is it?

... Dirt Devil Vacuums

How to install a new power cord on a tristar vaccume

You must flip the Tri Star upside down to reveal hidden body screws. Generally 2 at back near the wheels and one at front below the cord retainer. Once removed the body will separate at the bumper. Before removing the motor , note the positio ... Vacuums

Need new power brush

Hi let me try to find that part for you. I assume color will not be an issue. will get back to you as soon as I can ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need new switch for Shopvac QSP Pro 10 gallon unit

I just went through the same problem with a Shop Vac. The switch is easy to replace but not easy to find. After removing the switch, I found a match made by Sigma Switches. They directed me to contact a local RV dealer and look in either their Coa ... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0873 seconds