Having problems with your Vacuums ?

I cant find the belt in my eureka altima bagless. I am trying to change it and I cant even see where it was or goes.


Answers :

On the hood of your vacuum, right behind where the brushroll would be at the front, you should see a silver screw on each side. Just remove the 2 screws and lift off the plastic hood. Your belt will be on the right side as you face the unit.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cant find the belt in my eureka altima bagless. I am trying to change it and I cant even see where it was or goes.


On the hood of your vacuum, right behind where the brushroll would be at the front, you should see a silver screw on each side. Just remove the 2 screws and lift off the plastic hood. Your belt will be on the right side as you face the unit. ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I HAVE TURNED THE VACUME UPSIDE DOWN TO CHANGE THE BELT AND A SILVER CLIP HAS COME OUT, I CANT SEE WHERE IT GOES AND I CANT DOWNLOAD THE MANUAL


Probably an edging clip ... Vacuums

How do you change the belt on the eureka 3281az ? can,t get the plate off the vacuum to see even where the belt would go ? thanks!!


... Eureka WhirlWind 4381 Upright Vacuum

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

I have an older canister and am trying to change the filter but cant see where it goes or how to access the old one... thanks


On the hose end top of the body there is a rectangular button push this downward while pulling on the front hatch. The hatch will swing towards the floor and the bag slides straight out. It's a good idea to brush the debris from the rear backup filte ... Electrolux Guardian Bagged Canister Vacuum

I was trying to change the belt but took too many screws off and also a spring. Now I can't remember where the spring goes. where can I find the schematics?


Click this link for schematichttp://www.ereplacementparts.com/hoover-uh71209-whole-house-cleaner-parts-c-37315_37337_2023 ... Hoover Whole House Bagless Upright, UH71209

I am trying to replace the brushbelt. I have the brush off not surewhich end goes where. also I had it on once but the belt was off when it was supposed to on. I cant find my instructions ! help


I am going Kirby "G" crazy.\015\012I hope this URL will be of help to you:\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039\015\012\015\012If it is of help, please rat ... Kirby Ultimate G Bagged Upright Vacuum

Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!


On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

CHANDE BELT HAVE A EUREKA ALTIMA AND CANT CHANGE BELT


You can find out how to change the belt in the manual here that I included on page 4.\015\012\015\012http://www.eureka.com/servlet/FindOwnersGuide ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water


Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Belt cant find out how to change hover belt


Not sure yet, but I assume you mean the belt that drives the brush at the base.\015\012If it is an older style cleaner, there would a be cover held on by a few screws.\015\012This hold the brush in place so tkae note of how it is in place ... Morphy Richards Vacuums

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?


My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

Where does the belt go on the kirby as i can not see what it runs of . One side goes on the drum with the brushes but cant see what it runs on


Were dose the belt go on a kirby ... Kirby Generation 3 Bagged Upright Vacuum

The roller has stopped rotating and I wanted to see if the belt needs changing. I cannot find out how to get to where the old belt is located.


Remove the bottom to find the belt. There is usually a spare in the compartment. I think there is 8 or 10 screws.\015\012\015\012Thanks for your interest in FixYa.com\015\012 ... Oreck XL21 Bagged Upright Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed


... VAX Appliances Vax X3 Bagless Upright Vacuum

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?


DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I cant find where all of the hoses goes and trying to back together a bissell 9500


Here is the manual on page 5 it tells you how to put together. \015\012\015\012http://www.bissell.com/images/UserGuides/9500_107.pdf ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0890 seconds