Having problems with your Vacuums ?

My kenmore centtral vac runs but does not ****. HELP11

\015 My kenmore vacuum runs but there is no suction.\015

Answers :

Does any of the inlets have suction or no sustion anywhere..if they all have suction except on then thats the one that has the clog.if there is no suction anywhere,go to the canister and find the main suction tube coming out.try to disconnect it then turn it on and see if you have suction them.if you have suction there then your clog is where the suction tube branches off and goes to each individual room.if you have a small drain auger you can stick it in the tube until it won't go anymore,when that happens you have found the clog,turn the auger and grab whatever is in there and pull it out.also check the filters and make sure they are clean and the canister is not full.please leave feedback
#1 i assume u checked the bag and filter if so equipped?
#2 verify the hose is not plugged
#3 verify hard plumbing not plugged by taking something metal (quarter) and crossing the 2 little metal nubs at inlet (don't worry it is low voltage u wll not get shocked) it should ****
#4 if hard line plugged you may need a second vacuum to reverse flow
are all outlets not creating suction f so detach vacuum from piping and verify that vacuum is not the problem
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kenmore centtral vac runs but does not ****. HELP11


Does any of the inlets have suction or no sustion anywhere..if they all have suction except on then thats the one that has the clog.if there is no suction anywhere,go to the canister and find the main suction tube coming out.try to disconnect it then ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Kenmore 116 Progressive Canister Won't Run


In the canister there is a fuse wire, also a circuit board that could be bad, I would check the fuse wire first. If the motor has a thermo protector on it, it may be open. The switch asm. in the hose handle could have gone bad.\015\012\ ... Vacuums

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

On my Kenmore 36932 upright vacuum, the agitator continuously runs. It runs when the vacuum is turned off.


... Kenmore Vacuums

Shop-vac model 90L550A motor wont run


Yes replacing the link would work, but that would not fix the cause. You have either pulled the wiring to the point of pulling apart the connection or there is a short. Which would be in the way of a grounding effect causing the link to heat and melt ... Vacuums

I have a Kenmore Model 116 26312603 sweeper. The vacuum motor does not run, the power head does run. What is the most likely solution?


If the switch is a simple on/off switch,it could be that.Make sure it is unplugged.If you take the switch apart,twist the two wires together,and cover with electrical tape.If you do not have electric tape,make sure the connection is off of the ground ... Vacuums

My dyson vac will run normal then lose suction with a ouder running sound


You need to change the belt. Here is the belt you need and the manual:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

RICCA VACUUM PROBLEM **** GOT CAUGHT IN VAC NOW VAC WON'T RUN


... Riccar 8650/8625 s Vacuum

I HAD MY DC17 VAC FOR 3 YRS NOW NO PROBLEMS AT ALL, I REGULARLY CLEAN THE FILTER LIKE IT SAYS BUT LATELY I'VE NOTICE THAT THERE SEEMS TO BE A LOT MORE COLLECTION ON THE TOP OF THE FILTER WHEN I'M DONE VACUUMING. IT HAS ALSO STARTED THIS WEEK TO MAKE A VERY LOUD HUMMING TYPE NOISE WHILE RUNNING, I HAVE CHECKED FOR ALL POINTS FOR ANY BLOCK AND NOTHING AND NOW TODAY IT RUN A FEW MINUTES AND STOPS AUTOMATICALLY,IT WILL RESTART AFTER I LET IT SIT UNPLUGGED.WHATS UP WITH THIS THING, IT HAS BEEN GR


The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work


If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

For the first time, I tried using my Kirby Sentria shampoo attachment. I've lost the manual but found instructions online for making the swap from regular vac to shampoo-er and got it all assembled. The foam laid down just fine, however, when I run the vac back over the foam to pick it up, there is not a stitch of water showing up in the tray. First I thought maybe it was bc I hadn't put that much of the foam/water onto the carpet, but 12 hours later, the carpet is still wet in spots. Clearly


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=638285\015\012Generic problem for all Vacuums\015\012For the first time, I\015\012Posted by MHicks on J ... Vacuums

On my kenmore central vac no power unplug unit plug it back green light comes on but try turning vac on green light goes off again .


Please clarify that we are talking about the central vac LED/switch panel panel and plugging it into a 110 V wall receptacle. If I understand when you unplug from the power source ,then plug back in the green LED comes on, looking normal ? But ... Easy Flo EF1400 Central System Vacuum

Was running fine, while pulling vac electric cord got tight and stopped running ,,,,,,,any clues,,,thanks, Abb


You have stretched the internal wires of the power supply to a point where they have parted \015\012\015\012You need a man that can to strip the cable back and re-join it ... Shop Vac 201-13 Wet/Dry Vacuum

Vacuum will not run on manual or tool setting, but if the tools plugged into the outlet on the vac the tool will work, but not the vac itself


... Festool CT22e Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

Kenmore Manual I am looking for a manual for a Kenmore Central Vac ....model # 34630


Sears/Kenmore central vacuum systems are no longer being made ergo no manuals available,especially on line on line. If contacting Sears parts directly, maybe one may be purchased ?\015\012\015\012 ... Kenmore Vacuums

Need the manual on how to run (put together and all) the hoover steam vac v2 (widepath) with auto rinse) we tried today and when we leaned it back (so we could run it on the carpet) water started pouring out all over the machine and got the carpet (like flooded) wet :( this one was me mom's and she passed on approx 2 1/2 years :( she always kept the manuals for everything but we caint find this one :( ... thnx


God Bless Your Mom.\015\012\015\012Hope this was helpfull to you. Sawdust46\015\012\015\012http://www.hoover.com/pdfs/manuals/F7411900.p ... Vacuums

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!


Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0594 seconds