Having problems with your Vacuums ?

Went to get some water for the Bissell Petwash power brush, when I reconnected it, the water is not coming through the house. The vacuum is working, just not the water.


Answers :

Try this...... take a part the upper half of the machine and\015\012look for the heater.take off one of the hoses and plow in it to see if it is clogged it is take a part and clean out .
\015\012what happens is it gets clogged with soap and water when it drys out\015\012\015\012\015\012
\015\012
\015\012The flat belt on you machine has an access panel to it from the side of\015\012the machine. That belt runs the pump if it is broken or came off the\015\012machine won't pump.
\015\012
\015\012Check to make sure both of the red/black circular rubber gaskets on\015\012either solution or recovery tank are on the tanks and not stuck down\015\012inside the inlet valves on the machine itself.
\015\012
\015\012Make sure there is fluid in both tanks. Without fluid in both tanks the pump loses prime and will not work.
\015\012
\015\012If all that checks out then you are down replacing the pump, but\015\012usually when the pump goes out, you will have a short burst of water\015\012when you first turn it on and then it stops working.
\015\012
\015\012Hope that helps you out-Good Luck
\015\012
\015\012
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Went to get some water for the Bissell Petwash power brush, when I reconnected it, the water is not coming through the house. The vacuum is working, just not the water.


Try this...... take a part the upper half of the machine and\015\012look for the heater.take off one of the hoses and plow in it to see if it is clogged it is take a part and clean out .\015\012what happens is it gets clogged with soap and wate ... Vacuums

I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of


... Miele S300 Bagged Canister Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water and cleaning solution not dispensed when pressing the switch. Heat light is on, water and solution containers are full, brushes and vacuum working. Selector is on floor clean and not brush clean.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke


Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!


... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.


It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vacuum isn't working. The red light indicator comes on seconds after I start it, yet there is no blockage and the brush area is free of debris. I checked all the filters and no sign of blockage there either. The brushes don't turn and there is no suction. How can I fix it?


Brush motor not working. ... Fantom Vacums Cyclone XT Upright Vacuum

Miele s7000 I first got the vacuum and used it for 20mins then the vacuum just lost the suction, the brush works but it just push the dirt around the house and I can see the dust and dirt flying around.So, I thought maybe the bag was fulled so I put the new bag in but still pushing the dirt around. What's wrong with it?


... Vacuums

Water will not come out to do floor work


HI, I have a very similar Bissell. My problem was that after unscrewing the top plate and looking at the pipes the pipes feeding the front sprays were full of gunge blocking the sprayheads. I managed to flush it through by carefully removing the T co ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No water coming out of the main cleaner at the brush


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell Proheat 2X Carpet/Upholstery cleaner and I can't get the soap and water to come out of the attatchment. The vacuum part is working, but the spray isn't. I can see the fluid is trying to go up the tube but won't spray. Help. Peggy


Hello, I have a Bissell "Little Green" cleaning machine that acted like yours. I found several clogs in the fluid system. The power for the fluid in my unit is provided by a small AC motor independent from the vacuum motor attached t ... Vacuums

Brushes work, but isn't dispensing water - Hoover F7220900 SteamVac V2 Upright Vacuum


... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a Polti leco aspira 710. The water in the tank is heating but when the trigger is activated no steam comes through. The machine is showing one green light and is emitting a continuous beep. The vacuum cleaner is working fine - but no steam at all


... Polti Vacuums

I have the Oreck Sanapathic DMS2000 Handheld Steam Vacuum, but no steam comes out when I push the button. I hear the motor, is there any buttons I am missing or any help on how to make it work, been plugged in for 5 min now. Held button down for 2... nothing. Just a drip of water.


ORECK DMS2000 No Steam First, tested tank and filter flow together using suction via plastic tubing. Worked freely Second, removed pump and disconnected hoses and terminals [watch location,three terminals on pump, two plugs] ... Oreck Sanapathic DMS2000 Handheld Steam Vacuum

I just bought a Dirt Devil 12 Amp upright vacuum which seems to work fine but it is blowing out air in the front just under the filter housing. I see there is a vent there but should there be any air coming out during normal use? Thanks Brandon Smith


Yes. For the unit to be able to take air in from use it has to exhaust air. This is normal. ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Hoover floormate Water will not come out-brushes move-suction works-just no cleaning solution--help!!


It seems to be a common problem with this series of floormate... some home quickfixes (a hassle, i kno) but put downward pressure while using the solution.... Check your warranty that came with it, and how long you purchased the floormate... Alot of ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Carpet cleaners brushes are not working, no water coming out.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hi i have a dyson DC 05 (yellow) vacuum which is playing up. it refuses to come on, but sometimes when you waggle the flex a bit it works after a while. Any ideas how I can get into the flex housing?


Thats your trouble You have a Dyson ... Vacuums

Sebo upright. Check brush light come on when in use. Vacuum appears to be working ok but seems a little heavy.


Try adjusting the height up ( higher the better ) also make sure the brush is turnig freely if not remove it ( push the button on the top of the brush roll housing and pull the side off ) and make sure nothing is stuck ... Vacuums

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?


Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1131 seconds