Having problems with your Vacuums ?

Nilfisk king 540: The cable is stuck. I can't take it out

\015 The cable of the vacuum cleaner is stuck, I can\302\264t move it. I can\302\264t take it out and the button to collect it doesn\302\264t work either. \015\012\015\012Product: vacuum cleaner Nilfisk king 540:\015

Answers :

Tools required: Haxalobular screwdriver (Torx or 'Star'), Strong hands/fingers, flathead screwdriver.
\015\012
\015\012Possible hazards: sharp edges (metal plastic), bacteria enriched dust/dirt.
\015\012
\015\012Notice the black ring/skirt near the bottom of the unit...sit on the vacuum cleaner, and pull very firmly at the ring, which will begin to click and pull upwards, rotate around the unit pulling the ring up until the whole ring comes off and you can pull it off over the top of the unit.
\015\012
\015\012Now, there will be a white plastic ring revealed around the unit, using a Flat Head screwdriver to pry the ring out of the grooves it sits in (pull it off towards the bottom of the unit as opposed to the intial black ring coming off upwards).
\015\012
\015\012Now take the handle of the unit and give a firm **** upwards, the whole encasement will slide off in your hand.
\015\012
\015\012You will now see the spring loaded cord retracter. The problem here is that the spring has become too losely wound back onto the larger spindle, or it is dirty.
\015\012
\015\012Firstly pull the entire power cord through the outer shell that you removed (you will need to unscrew and remove the black facade that the cord goes through otherwise the head of the cord wont go through).
\015\012
\015\012Then take the plastic cirlce cover off the smaller spindle (carefully as the wound tin spring could pounce).
\015\012
\015\012Now you need to manually turn the larger wheel clockwise until it has no coil left on it, and the smaller coil now is full.
\015\012
\015\012While winding, dont let the powercord wind back onto the wheel, let it sit to the side (there will be a bit of tangle which will go back to normal when we finish winding back the other way).
\015\012
\015\012Once it is fully loaded onto the smaller coil, wind it back on to the larger coil again, but make sure it's loading on 'tight'. You can ensure this by keeping some pressure on the smaller spindle while winding (be carefull because the coil edge is sharp). Once the smaller coil is basically gone and there is just a small curved end of the coil, put the small spindle back on making the curved coil wrap around it.
\015\012
\015\012Wind some coil back onto the smaller spindle so there is atleast one full ring plus a small overlap, around the spindle, or it may come off. Also, make sure that where the cord is coming out of the larger spindle, is pointing towards where it goes out the back of the vacuum cleaner, so that when you pull the cable it wont wind the wheel at all, otherwise it may wind some coil off the smaller spindle.
\015\012
\015\012Proceed to put the unit back together, but before putting the white and black rings back on, test the retract button. I noticed the first attempt to put it back together that the external button had not lined up with the internal mechanism and it wouldnt retract, i had to open it again.
\015\012
\015\012All done, it should now retract, but it will never be as strong as the day you bought it, but atleast you dont have to have the cord hanging round. Hope this helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Nilfisk king 540: The cable is stuck. I can't take it out


Tools required: Haxalobular screwdriver (Torx or 'Star'), Strong hands/fingers, flathead screwdriver.\015\012\015\012Possible hazards: sharp edges (metal plastic), bacteria enriched dust/dirt.\015\012\015\012Notice the black r ... Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine


... Bosch Vacuums

How do i take apart a nilfisk king 510


... Vacuums

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


I'LL DO A SEARCH ON LONE BUT THE MODEL NUMBER WOULD HELP ... Vacuums

Nilfisk King Home: the cable will not rewind - Vacuums


... Vacuums

How do I fix the cable rewinding on my nilfisk king


... Vacuums

HELLO MY nilfisk king 540 cable will not retract. I have taken the machine apart and the coil has now come off the small spindle. is there anything you can do to help me


... Vacuums

I have adyson dc04 the cylinder is stuck cant get off to clean it out


... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.


Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.


Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum

How do i take apart the dyson,Theyre is something stuck in the hose extension. Is theyre anyway to take it off. The bottom part works . however theyre is no scution threw the hose


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I am trying to replace the cable on a Hoover smart cyclone, however after taking all the screws out I can see the cover remains intact Can anyone help?


... Hoover Clean Smart Cyclonic Upright Vacuum

Low suction on Nilfisk King


... Nilfisk Family Vac Bagged Canister Vacuum

Nilfisk Coupe Neo power cable jammed


... Nilfisk Vacuums

I can't figure out how to take apart my Panasonic MCE737 Vacuum cleaner to repair the retractable cable, can you help


... Vacuums

Motor is noisy like there is something stuck in it. I am looking for the service manual so I can see how to take it apart/


Hi\015\012Generally modern upright vacs don't have screws that you can undo to get into the motor and most Electrolux/Eureka models have sealed units. I suggest looking at the sole plate where the roller brush is, check for anything clogging the main ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

How to take off motor on the dirt devil kurv, my start button is stuck


... Dirt Devil KURV Hand Vacuum Champagne Vacuum

How do I get my vacuum cleaner to blow air instead of **** air? I want to use it to blow up an air bed - Nilfisk King 240


... Nilfisk Vacuums

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in


Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover u6632900 the self propelled black plastic piece that the cable attaches to is broken. how do i take the cover off to get to the piece and replace it?


... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but


Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Cleaning I cant take the cup out to empty it


Don't bother emptying it. It just clogs, brush won't turn, won't even vacuum up a staple on low pile - office-type carpet. The filters clog, the cup clogs, and frankly, your time is worth more than the $50-75 to replace this vacuum. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0321 seconds