Having problems with your Vacuums ?

Vacuum stopped working

\015 Vacuum was working and stopped now it will not turn on\015

Answers :

Could be a bad cord, sometimes it can be a switch.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Stopped working while vacuuming heavy dust on patio the vacuum suddenly stopped working. I tried it on other outlets with no luck. I cleaned the filters and still no luck. Is there a circuit breaker if it get hot?


It cooled down and worked 20 minutes later ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?


Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

I have Hoover WindTunnel Air Upright Vacuum - UH70400 just used couple of times. While vacuuming the carpet carpet fringes were rolled up in to brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.


... Hoover Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?


Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover Vacuum works, then stops in 3-5 mins. Works again in a couple of hours


More than likely there is an inline over current breaker that is bad or weak and needs to be replaced. This is for overcurent protection of the motor. It is fairly common for the protection circuit to go bad ... Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank


You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

Vacuum cleaner stopped working while vacuuming. Turned off unit and it would not go back on. All electrical outlets tried and it still did not work.


The power coupler might be faulty, price the coupler and the decide whether its cheaper to replace it or the vac. ... Vacuums

VACUUM ONLY WORKS FOR 45 SECONDS THEN TURN OFF ITSELF. I HAVE TO WAIT FOR 10-15 MINUTES TO START AGAIN USING IT, STOP WORKING AGAIN AFTER 45 SECONDS. VACUUM IS NEW, I COULDN'T RETURN IT TO THE STORE I BOUGHT IT. PLEASE HELP ME TO RESOLVE THIS PROBLEM. THANKS


Sounds like it overheats quickly. But why are you not able to return it? ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Cleartrak vacuum suddenly cleartrak started to make weird loud noise i cleaned. When it got jammed I stopped the vacuum and dislodged the jam and it worked fine. How to stop the weird loud noise?


... Vacuums

Have problem with mine my Z8280 Electrolux vacuum cleaner. It has stopped working. Did all the trouble shooting cleaned everything even though this had been done previously. Turned it on and it only worked for a few minutes and then stopped.


... Electrolux Vacuums

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.


Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

My dc16 dyson root vacuum stopped working abruptly with no indication of a weak battery, the charger does not show a charge on battery. usually the vacuum slowed before it stopped with a dead battery, any suggestions


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Hey I have a kenmore model 116.23185800c vacuum. The vacuum stopped working but the power head still works is there a reset for the motor


... Kenmore Vacuums

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.


Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015


You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum

Have problem with mine my Z8280 Electrolux vacuum cleaner. It has stopped working. Did all the trouble shooting cleaned everything even though this had been done previously. Turned it on and it only worked for a few minutes and then stopped.


... Vacuums

Pro action vacuum stopped working whilst vacuuming


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0717 seconds