Having problems with your Vacuums ?

I have the Bissell Flip Ease (vacuum/mop) and threw away the instrux on how to load the cleaning solution...and I can't get the clear plastic holder off the fixture. Anybody know which buttons to push?

Answers :

For the water tank - you just pull up on it and forward motion. for the dirty tank there is a button at the top you pull down on.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the Bissell Flip Ease (vacuum/mop) and threw away the instrux on how to load the cleaning solution...and I can't get the clear plastic holder off the fixture. Anybody know which buttons to push?

For the water tank - you just pull up on it and forward motion. for the dirty tank there is a button at the top you pull down on. ... Vacuums

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.

If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.

For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it ba ... Bissell Vacuums

Beater bar does not turn. Pushed in motor Reset button after clearing bar, but no change.

Belt broke and needs replaced. ... Kenmore Vacuums

I am working on repairing a model S3101W shark steam mop. I took out two screws and took off the swivel head and a short clear plastic tube fell out. I do not know where it goes. No spring fell out with it. Where does it fit? What holds it on. Thank YOu

The same problem Im having, and Im not a handy person at all..Im about to junk it..I have no idea what Im doing :) ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine

... Bissell 8910 ProHeat Clear View Upright Vacuum

I have lindhaus activa 30. It was clogged and then cleared of the clog. When the power button is pushed, both red and green lights come on and the green turn off immediately. But no motor....

Motor might be burnt up from the clog. ... Lindhaus Activa 30-38 Bagged Upright Vacuum

I have an Ellies wizard 4 remote control but lost the manual. Unable to set up to LG tv dont know what buttons to push.

... Vacuums

Dyson DC05 It is a vaccum cleaner in a perfect condition but recently developed a problem. It sparks and sometimes power goes off while operating. It is clear that the wire is loose but do not know how to open the bracket of the main button on the machine. [email protected]

Hi \015\012try this site http://dysonmanuals.llc.nu/\015\012\015\012It has service manuals for the DC05. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I need to know how to use the reverse on Husqvarna 5710, My manual is in German, I push the middle button doesn't work.

... Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.

... Panasonic Kenmore Canister Vacuum Vacuum

I also have a hyundai electronic safe and I've forgotten my password. I know I need to push the center S button first but that;s all I remember. I have the serical number if that'll help.

The serial number is of no use. If you could obtain the combination simply by asking on a public website then your safe would be, by definition, an unsafe... Many electronic safes come with an emergency bypass key, so check that you haven't got one ... Vacuums

I replaced the motor in my 6500SR Epic vacuum cleaner. Now I have 3 clear plastic hoses for air flow. I know where two of them go, Im not sure where the third air hose goes? Jan

All three are connected to the control valve assembly.\015\012The long one goes through the hole in the bag container and to the door and inside.\015\012One goes to the bottom of the bag container.\015\012The last one goes to...I ca ... Electrolux Vacuums

My walkie talkies won't turn on. We've only used them a few times, and not recently. I charged the batteries, but it doesn't seem to want to switch on. I've pushed that grey side button. Is it possible that it's locked off? And, same problem is with both of them. Seems a basic question, I know. They should be working though. Thanks, Bruce

... Vacuums

Motor just makes 4 or 5 small clicking noises when you pull the trigger, then stops. The little lights illumintae around the "max" button as well. However, the motor does not engage in the slightest. There is no blockage at all. I have owned the vac for 10 months and know the sounds of blockage and clear them immediately. I just used it in the morning, plugged it back in and it has not worked since. Any ideas?

... Dyson DC35 Handheld Vacuum

Euro-Pro X model SC410. Unit heats water but when I push the power button, it just hums.... Where can I get it repaired? or does someone know what type of tool is needed to unscrew the screws on the machine?

... Euro-Pro S3325 Handheld Steam Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri

Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.

... Eureka Vacuums

Dyson DC35 beater bar stays on when power button isn't pushed

... Dyson DC35 Multi Floor Digital Slim Cordless Vacuum

I have a DC24 dyson and it is not having suction without white button on canister pushed in.

Hi there, it's Jack at Dyson.I'm sorry to hear your DC24 doesn't seem to be working as well as it should be. The white button you've described is the suction relief valve - this helps protect the motor if the machine is used when blocked. ... Dyson Ball DC24 Bagless Upright Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

My swan steam generator iron s15040n is showing a push button when it is turned on. im pushing the button but it continues to say push and keeps beeping. the iron wont turn on at all. please help!!!!! thanks

... Vacuums

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu

Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'

Machine will not come on ... Kirby G6 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0506 seconds