Having problems with your Vacuums ?

Replacement wand for canister

\015 Hi,I have a Eureka Oxygen vacuum model 6996 type A. The electrical cable for the lower wand has partially melted the connector that joins to the beater unit. the simplist fix and cheapest would be to replace just the cable as the wand is fine. the second solution would be to find a lower straight wand that does not have the "sensor" (a dumb gimmick) but I don't know if it would fit. The last idea is to get the overpriced wand with the sensor.Ultimately, it would be nice to know why the melting happened in the first place. It did happen when the vacuum was new, then the top connector melted and the wand was replaced under warranty. This second malfunction took years to happen. The prong that seemed to overheat looks rusty. I'm wondering if the electricity was somehow impeded there and caused a heat buildup.anyhow, love anyone's thoughts on this.\015

Answers :

Whne you had your first problem with it, the cord at the bottom probably should have replaced also, if one end gets scrotched, the other end does also. One big reason why this happens is connecting and dis-connecting the power head while power is still applied to it. When you hook your skillet and it is turned on, it will arc, so does the contacts on the hose and power head. That prong is rusty, it is scrotched. Don't know if you can substitude, you might try to find a shop that has other wands and see if you can find a fit, either that or buy the one that is supposed to be with it.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C

... Filter Queen Majestic Canister Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

Replacement wand for canister

Whne you had your first problem with it, the cord at the bottom probably should have replaced also, if one end gets scrotched, the other end does also. One big reason why this happens is connecting and dis-connecting the power head while power is st ... Vacuums

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?

Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

How to replace wand release on handle of sweeper canister model 116.21614

... Kenmore 25512/ 25513 Progressive Canister Vacuum

We have a kenmore canister vacuum, the part that is attached to the wand that picks up the dirt doesn't work, when it's on the carpet the light does not go on. Do we need to buy a new vacuum or is there a replacement for this part.

Hard to say without the correct model number.\015\012\015\012However, you could check these things first:\015\012\015\0121- Is the belt that runs the brushes on the end pieces broken? If it is, is needs to be replaced.\015\0122- Is there ... Kenmore Vacuums

The vaccum cuts out replaced the wand but still having the same issue - the powermate head is fine and does not appear to be causing the problem. I have two Kenmore Progressive Canister Vacuum and this is happening on BOTH

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!

Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

My wand on my canister began to spark and snap and smoke. The element was melting. and now I am stuck with only a working canister. the elememt or electrical hook up is burned up...and I guess I am gonna have to BUY ANOTHER wand or connection??? I don't know what to do... but this is a HUGE dissapointment. The canister still works... but no vacume head.

How's the hose?\015\012If it's only one wand, yes, you'll need to buy a new one. It depends on where it burnt out. If it was at a connection to the hose, the other wand, or the power nozzle, you need to check the connections thoroughly for di ... Electrolux Lux 5500 Canister Vacuum

I need to replace the part of the wand that

Try espares .co/uk ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Miele Filtration Guard S528 Canister Vacuum telescopic wand repair

Hi There, you certainly can get a ... Miele Filtration Guard S528 Canister Vacuum

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?

There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!

... Dyson DC05 Bagless Canister Cyclonic Vacuum

Need to replace power cord and can't find how to open canister to replace

I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dust collects on outside of canister on Hoover twin chamber bagless cleaner . I have replaced the filter & rubber gasket at bottom of the canister ,checked for blockage.

... Hoover Vacuums

Replacing the extension wand terminal cover

Hi, It has been a while since I had to take one if these power heads apart. The Sears Service maual does little to explain the exact removal procedure of the cover. But from memory here goes. \015\012\015\012There are pressure locks on ... Kenmore Vacuums

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@

Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

How do I attach the rainbow mate to the rainbow canister or wand? I have the D4C model, My electric hose is original but does not have the grip handle. Does that matter? The cord is so short it cant just attach to the canister right? thank you very much.

... Rainbow 75th Anniversary Canister Vacuum

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available

Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0388 seconds