Having problems with your Vacuums ?

Bissell 3510 Vac with loud noise but not belt

\015 Have Bissell 3510 vac. that makes a racket when you turn it on.Cked base & belt, but not there but in the motor base assembly. Have got schematic, but not sure what I am looking for or is it worth the time? Thanks,Gary\015

Answers :

I had the same problem with my easy vac as well after owning for almost 2 years. I cleaned ALL the filters, the brush, the hose, even changed the belt...nothing worked. Then i took a flashlight and looked along the side where the belt i located. I am betting u will notice the same issue i found...the belt wore away a small hole/indentation in the side. If you take a little masking tape and cover the hole, the loud noise stops and your suction is returned. The tape has held up a few months for me so far. I wish this site let me post pics so you can see how to do it.
Did you check the brush roll, may have a problem with it. But you could have a problem with a motor bearing going bad, they getting loud, also if there is a problem with the motor fan, that may be the cause of it being loud. Bissell 3510 either is obsolete or is thw rong number, it doesn't come up at the Bissell site.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell 3510 Vac with loud noise but not belt

I had the same problem with my easy vac as well after owning for almost 2 years. I cleaned ALL the filters, the brush, the hose, even changed the belt...nothing worked. Then i took a flashlight and looked along the side where the belt i located. I am ... Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt

... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell model 1694 rug scrubber works for a while then makes a loud noise when you pull it toward you like it is. Umping over something, roller is very easy to pull on, is it loose or a belt?

Dear Sir:Possible the motor can be faulty, or test the belt if is crack and replace. However you must see if there are some debris inside. Please see the section troubleshooting in your user manual. Download Biseel.com or www.fitness.manualsonlin ... Vacuums

My bissell is making loud noises. I looked at the belts and they are fine what could be the problem?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.

Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Steamer is making a loud grining noise and smells as if something is burning. We just replaced both belts.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Vacuum problem i have a bissell total floor velocity and everytime i turn it on it makes this really loud noise like it's about to exploded. We changed the belt but that wasn't the problem and we just bought the vacuum a little over a year ago.

Check the brush roll, do the ends turn freely, if not, replace it. Could have a clog in the hose or the dirt inlet by the brush roll, the other could be a bad motor. ... Vacuums

6579-2 bissel power force. Belt was broken. Purchased new one. replaced. making loud noise and smells like burning. HELP

... Bissell 6594 PowerForce Bagless Upright Vacuum

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough

The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Loud noise from Bissell Powergroom beater bar

... Bissell Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help

I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

My bissell is making loud noises when vacuming

... Bissell Powergroom Pet Vacuum

Bissell 8990 CleanView Bagless Upright - Loud noise

Sounds like maybe your motor went bad, part # 2031052. Would sell for about $60. When the bearings go bad, they can be real loud as well if the fan on the motor when it gets damaged. ... Bissell 6590 CleanView Bagless Upright Vacuum

My Bissell Cleanview Bagless vacuum makes loud grinding noise.

The ends of the roller have something wrapped around them.see if you can pull the ends off so you clean the caps and bearings ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

It's making a very loud noise when running. I have a Bissell Quicksteamer series 2080. When I was using it yesterday it was making a light squealing noise then it turned into a loud racket. I shut it off and and cleaned the brush (lots of dog hair on it) But the racket continued.

... Bissell 1770 Quicksteamer II Upright Vacuum

My bissell momentum vacuum is making a very loud noise but it still picks everything up. Do you know of a reasons why it is making very loud noises. I checked and nothing is stuck in it.

It might be the motor or the fan is messed up.have someone or you check that out. ... Bissell Vacuums

Dog hair gets caught all the time in the belt drive spool, is there a fix for this other than having to pull it out all the time by hand? I have replaced the belt and the brush but this hasnt solved the problem and the belt moves so slowly and I get the loud whining/grinding noise too.

It could be either the clutch, the beater bar or the brush housing. I have included links to each parthttp://platinumvacuum.com/dyson-dc07-dc14-clutch-assembly-900252-04.htmlhttp://platinumvacuum.com/dyson-dc07-dc14-brushbar-assembly-9041 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My brush is no longer working on my bissell healthy home vac. when i try to turn it on it makes a high pitched squealing sound. I'm pretty sure it needs a new belt but my husband is having trouble getting the vac. apart. He says you need a special tool to get the screws out of the bottom of the vac. Any advice? THANK YOU!

Hi,\015\012 According to Bissel, they should be standard phillips screws. Nowever - things change.\015\012This is a general guide from Bissel for belt change - \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Kenmore upright vac model 33922 - good suction but developed loud whining noise after accidentally vacuuming room without bag. Added bag and changed both filters. Still makes noise. How can I stop noise?

The bag is the first stage in your filtration. Most times what you did will draw fine dust right through the filters and into the motor itself, affecting the bearings and clogging the motor fans, throwing them off balance. The fact that there i ... Kenmore 33922 Direct Drive Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you

Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0641 seconds