Having problems with your Vacuums ?

Ball Bearing How to r&r ball bearing on fan assembly?


Answers :

On what are you wanting help with. If this is a vac, what is brand and model number???
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ball Bearing How to r&r ball bearing on fan assembly?


On what are you wanting help with. If this is a vac, what is brand and model number??? ... Vacuums

Ball bearing in brush roller


These can usually be purchased thru a hoover dealer and are not expensive. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?


... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

I need a "Bearing Assembly" for roller brush 61445-1,I Have a GE 106575


Probably should just go to a repair shop and they should be able to order one for you, that is if they are available by themselfs. Or if you have a store where you live that sells vacuum parts, you could go there. ... GE 106585 Upright Vacuum

KIRBY G4 FAN ASSEMBLY ORDER


First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don't tighten too much just beyond hand tightening). Pu ... Vacuums

I have a Simplicity (Danby) SDR458H Dehumidifier. The bearings in the fan motor have become loud and scratchy sounding (due to a plugged-up filter in the past). I would like to get a repair manual for it with part numbers so I can order a new fan motor.


... Simplicity Vacuums

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?


No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

My Dirt Devil Model 088520 has a brush assembly that wont spin. How can I either change the bearing or free it up somehow? I have been searching for a new brush assembly part number 2860145000 but it


Try this link > http://dirtdevil.com/parts/category/brushrolls-uprights/ ... Dirt Devil Vacuums

The bearings on the fan side of the motor were extremely bound. I was able to free them up with WD 40. Should I pack the bearings with grease?


The bearing on electric motors are normally sealed bearings so no dust or dirt can get into them, if i were you while you have the motor out i would get new ones the number will be on the side of the bearing and are very cheap to buy, ... Oreck XL Ultra Bagged Upright Vacuum

Replacing the bearing behind fan on a kirby heiritage II 2hd


I don't know what model of Kirby you have but on all Kirby's that I know of you have to remove the fan. Here are two vid's on fan removal for a generation series vacuum. ... Vacuums

The ball bearings are stripped from the roller brush of the power head for my electrolux model N115M


You will most likely have to replace the roller brush wth bearings. i just recently had to replace my wifes on her electrolux. i was able to order the parts online at sears parts direct, but there are many places to get them online. you will need the ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Replacing fan assembly on Kirby G2000 - Vacuums


This video should get you half way there:\015\012Kirby belt replacement\015\012\015\012Hope it helps ... Vacuums

Do you have an instruction manual to assemble a ceiling fan with light kit. I think it's an old Hampton Bay model TU-403 file #E89510


... Vacuums

Looking for the roller part number for Eureka 2961AVZ. The ball bearing on one of the side broke on the existing roller.


You should be able to find the roller you are looking for at this URL:\015\012\015\012http://www.vacuums24x7.com/eualseup29se.html\015\012\015\012Paul ... Eureka 2961AVZ Bagless Upright Vacuum

How do i replace the fan blade assembly which are broken in my ureka model the boss thank you lorne


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=540001\015\012 \015\012Generic problem for all Vacuums\015\012How do i replace the\015\012 ... Vacuums

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum

When replacing bearings I got confused on how fans go back onto the shaft. Please help, Pictures would be fantastic. Thank you, David


Need to repair power cord ... Rainbow Vacuums

My Dyson makes an almighty racket and its something to do with a ball bearing - can you help?


Hi there, if you have a machine where you can switch the brush bar on/off, the machine can make a ratchet noise if the brush bar become obstructed. Its designed to do this to alert the user that there is something stopping the brush bar turning. ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I just cleaned my ecoquest freshaire prifier and after assembling the unit, the fan is making squeaking noise. what should i do?


Hi.You may need to replace the filter.Call Ecoquest at the number listed on the owners manual to get a replacement filter. Filter can also be ... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

The bearing mounted gear/cutter assembly at the bottom of my 6 month old GE 169188 blender has gone bad; it's very loose and leaks fluid. The part is easily replaced. Only problem is that I can't find the part anywhere I've looked online. What is the deal? Why dont they make such a simple part available for a nearly new cheap appliance????


Cannot find that model number.. However.. Contact GE parts and service.. here.. https://www.geapplianceparts.com/GEApplia ... Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

How do i remove the fan housing assembly from the handle connector on the 2600HH


There are two or three screws resest. ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0426 seconds