Having problems with your Vacuums ?

Does not **** properly - Vacuums

Answers :

Check all filters. Some of the newer vacuum cleaners have up to 3 filters that need to be cleaned and or replaced. Motor filter, Hepa Filter, and or Air Filter.
\015\012Make sure there isn't any clogs in any part of the hoses and or tubes.
\015\012Other than that... pretty basic. Motor sucks air through the filter, then through the hoses.
\015\012Good luck.
Hope this helps.
\015\012If this has helped, please rate my answer.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

I have a kenmore vacuum and the head of the vacuum is not turning as it should..what do i do? Everything else seems to be working...I tried to reset it but nothing happened. One more thing what is the head of the vacuum properly called?

Replace the belt on the vaccum. ... Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks

... Sunbeam Vacuums

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.

... Dyson Vacuums

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

I have a DC 15 Dyson Ball Vacuum. I've removed and cleaned the filter. I can't get the lid to close properly. I don't want to force it and break something. There is some kind of a red spring loaded tab that seems to be in the way. How do I reseal the top of the vacuum?

The red tab doesn't let the lid close if the filter is not fitted correctly or the wrong filter is fitted. Many after-market filters cause this problem. \015\012\015\012Have you recently fitted a new after-market filter? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Broken vacuum jammed the rotating brush on a kenmore powermate vacuum cant get it to run properly after clearing the jam

Question; you can't run it properly meaning? The agitator (brush) isn't spinning? If that's the case, then Kazong is right, check the belt. If the belt is fine, check to make sure you didn't damage the bearing of the agitator.\015\012\015 ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

Suction problems My Hoover elite vacuum (which is less than a year old) is not sucking up properly. Also, when I detach the tube that goes to the vacuum cleaner so I can add my attachments, it blows OUT dirt through that opening. HELP!

Sounds like a clog right near the front ... Hoover Elite U5061-900 Bagged Upright Vacuum

Kenmore vacuum not sucking properly - Kenmore 35912 / 35913 Progressive Upright Vacuum

... Kenmore 35912 / 35913 Progressive Upright Vacuum

My Morphy Richards vacuum cleaner (2 years old) will not pick up properly and also cuts out about vacuuming one carpet but then starts again later. Will I need to call our repair service?

Here are a few tips to try before you call a repair service.\015\012\015\012Most people think that putting their vacuum on the lowest setting picks up the most dirt. If you have medium to shag carpet, putting it on the lowest setting wil ... Vacuums

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!

... Sharp Twin Energy EC-TU2607 Vacuum

Electrolux 2 in 1 Ergorapido stick Vacuum. Motor runs then cuts out after 3 - 4 seconds. Sometimes it will run properly for 10 minutes so batteries are good. Why does it cut our usually?

If the hand held is working correctly (By itself) try pulling up a little bit on the 4 metal connection tabs on the wand. The connection tabs were not making a proper connection on my unit. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

How to properly put Kirby Sentria 11 vacuum cleaner back into original box

... Kirby Vacuums

Noisy vacuum that wont pick up properly

Your vacuum is still under warranty. Call Miele or the Miele dealer you bought it from. They are obligated to repair your vacuum. ... Miele S4210 Carina Bagged Canister Vacuum

Miele vacuum cleaner not working properly

Is the suction low or ok at the vacuum without the hose attached? If it is ok, then there is a clog in the hose. If it isn't, then check filters, is the speed variable, is the contol set too low. Could be a bad motor, running too slow. ... Vacuums

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom

... Vacuums

Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.

Check the belt and what got stuck in it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Installed a used engine on a 1996 Toyota Avalon xls, and need a vacuum hose diagram so I can run new hoses properly.

Your dealer should have the schematic for your vacuum lines. If not , Auto Zone sells the manual for your car type. However, it is not uncommon to have hoses left over. The extra hoses could be for accessories your car is not equipped with. Hope t ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0570 seconds