Having problems with your Vacuums ?

96 v6 mustang a/c only comes from top of dash unable to control

Answers :

This could be caused by a loose or broken vacuum line or a broken vacuum operator. It is also possible that the a/c switch assembly is defective. You'll have to inspect. If you want to know if a particular operator is working, use a piece of tubing attached to the operator and **** on it. If you don't feel a vacuum, the operator is bad. Hope this helps...but without actually working under your dash, this is the best I can do. Try your local library for a copy of the manual and vacuum diagram.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

96 v6 mustang a/c only comes from top of dash unable to control

This could be caused by a loose or broken vacuum line or a broken vacuum operator. It is also possible that the a/c switch assembly is defective. You'll have to inspect. If you want to know if a particular operator is working, use a piece of tubin ... Vacuums

Emission control valve has failed and all my dash light have come up

... Toyota land cruiser valve set, emission control. vacuum piping

Base Plate screw rotating in insert and not coming out. Insert come unfixed with screw still attached. Therefore unable to remove baseplate, unable to remove cotton fibres from brushes. Have you an engineer in the vacinity of york(NOT A SALESMAN WITH A FRANCHISE) PLEASE

Try to remove all other base plate screws first. If they can be removed gently try to pull open by hand against the lid while rotating the remaining screw. You will need to apply outward pressure betweent the insert and baseplate to remove it while r ... Vacuums

Keurig b200 problem; When brewing with cup in unit water will pass into cup and it seems when k cup is full the grinds puch up through the top and water overflows. i pulled out the k cup holder and cleaned so their is nothing that is obstructed included the piercing pin. brewed [product does come through but does not seem to allow it to come through fast enough or if it supposed to be pressurized it is losing its seal on the top of the k cup

... Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!

... Miele S7210 Bagged Upright Vacuum

Steam not coming out of the bottom of shark vacuum its coming out of the top

... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?

Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.

The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

Cap (top) is froze. Unable to remove cap (top) to pour water inside for use. not sure if model specified is correct. It's a canister with hose and multiple attachments for cleaning.

I too can not figure out how to get the lid off. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu

Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

I have a GE model #SCA1000HBB02. Recently the control buttons quit working. I thought maybe someone locked the controls but thats not the case. The display lights up shows the time but thats all. I unplugged it and then powered it back up the display comes up to set the time but the buttons will not allow. Any help would be appreciated. Thanks, Gary

Sorry but this is the vacuum area, your problem maybe the main board or a fuse. please go to the microwave forum. ... Vacuums

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?

... Panasonic MC-3900 Bagged Canister Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My cigarette injector nozzle on my Top-O-Matic keeps coming off. Why and how do I fix it? With glue? I put the tobacco in, and my empty cigarette tube on the nozzle, then use the hand crank to push the tobacco into the tube and the NOZZLE is coming off with the tube and the tobacco isn't filling the tubes. please email me back a response [email protected]

... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum


What kind of vacuum is it ? call me at 314-628-9153 and i will walk you through it ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My Dyson DC17 vacuumn system is stopped up, the clog is in the top part of the vacuum before it drops the dirt into the cylinder. Does the top part of the canister come off so that you can get into the tubes that are clogged.

... Dyson Vacuums

My cv353 will not come on when I plug the hose in, but will come on with the switch on the unit.Which control may be the problem? Thanks Larry

... Broan-NuTone CV353 Central Vacuum

Screw top not coming off

If you look under the black plastic cap (between the bottom lip of the cap and the yellow steamer body) you should see a circular hole in the pressure valve that the plastic cap is attached to. I used a flat blade screwdriver and a hammer to tap it ... Tristar SB Steam Buggy Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin

Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum

I have a 6 gallon shop wet or dry vac. The dust and dirt comes out around the base of the motor fin, not around the tank top. Now what? Oh I lost the filter around the drum that holds the ball, so I wrapped a rag around it and made it secure. Respectively: TOM

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=765231\015\012Generic problem for all Vacuums\015\012I have a 6 gallon\015\012Posted by tsfroggy on Jul ... Vacuums

My DC05 Dyson suction has stopped...there are no blockages, the seals are good, there seems to be more suction coming from a yellow box which is situated at the top of the removable cannister. There is nothing obvious'

My Dyson had exactly the same problem. I found the problem was caused by a blockage in the hose. Take the hose out where it joins the cleaner (it will come out if you pull it downwards gently) and take the hose out of the handle by squeezing the ye ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a dyson dc17 animal vacuum and hair and dirt gets trapped in the top part of the vacuum. does this come apart?

You can take this apart. There is a very good detailed explanation of how to do this here: http://www.exonotes.com/content/node/4\012\012I have done it. Now it sucks like new! ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Warter coming out of the motor on top when using on wet cleaning my carpet.

It is too full and/or the float is working.Take the top off and set it away from the tank and run the motor for 10 minutes to dry out the vacuum motor. Check that the float isn't stuck and be sure to empty the tank regularly ... Numatic GVE370 Canister Wet/Dry Vacuum

Water leaks out the bottom of vac have new tank but the water still comes out the bottom while running like it is automatic no control

Hi Steve I have the same problem can you help if you were able to fix? ... Hoover F7220900 SteamVac V2 Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I

Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0466 seconds