Having problems with your Vacuums ?

The vacumn runs but brush dose not turn belt is good. It's a dyson 110 us c 10417

Answers :

Now is it air driven or belt driven? It could be the belt that's not turning the brush. Check if the belt is loose or is broken. If it's air driven, then check and see how the condition of the bearings are. If it doesn't roll smoothly then you need to replace the brush roller. If it does roll smoothly then check if there's a blockage in the line.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The vacumn runs but brush dose not turn belt is good. It's a dyson 110 us c 10417

Now is it air driven or belt driven? It could be the belt that's not turning the brush. Check if the belt is loose or is broken. If it's air driven, then check and see how the condition of the bearings are. If it doesn't roll smoothly then you need t ... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush doesn't turn and belt apears good - Dyson DC07 Bagless Upright Cyclonic Vacuum

If your unit has a large knob on the right side of the cleaner head as you hold it when cleaning then your unit has a clutch this clutch has two belts in it so the brush belt may appear ok but the motor belt might be broken it is not an easy repaer ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good

Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums

Dyson dc 33 vacum the brush does not turn and belt is good and it has a high pitch grinding sound happens

... Vacuums

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.

This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position

I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

The brush roller will not turn. checked the belts, checked the brush roller gears and they are good too... the motor is not turning .. could it be a switch somewhere?

... Electrolux EL5020 Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Ratchet noise, beater will not turn, belt not broken, in carpet mode the Dyson d07 makes huge ratchet noise and the belt will not turn the beater brush.

Ok, so I had the same ratching noise and took the advice of many sites directing me to clean the brush. But like most I cleaned the brush and the noise continues and the brush does not spin. Reluctant to take it to get serviced I dug a l ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?

Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

I have a Dyson DC33 bagless vacuum and the beater brush is not turning .. How do I get the cover off the brush to change the belt?

If you lay it down so you can see the bottom of the vacuum, there should be 3 flathead looking screws,just turn them a quarter turn or so, and that bottom should pop off so you can take the brush out and change the belt, just make sure you watch how ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson animal and the brush will not turn i think it is the belt how do i check the belt or change the belt

Hello. In most instances, the problem is the belt. the problem with dyson, as all vacuum repair people will tell you is this. All other brands make it easy to change the belt. Usually for $5. or less. Dyson put the belt inside of an assembly whi ... Dyson Vacuums

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

My dyson hose sucks good but, when i put handle down, it won't **** but brush does turn

I just had the same problem....suction from wand, but no suction from soleplate, the brush bar spins. Did all the troubleshooting steps on dyson.com but they didn't work...dyson.com says need to take to repairman, being a diyer I went to search engi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1318 seconds