Having problems with your Vacuums ?

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


Answers :

The belt may have come of or broke..
\015\012Turn the vac over so the bottom is facing up..
\015\012Remove the scews in the plate cover that surrunds the brush..
\015\012Remove the plate cover..
\015\012You will see if the belt is on or if the brush is stuck..
\015\012IF the belt needs replacing - put the belt on the motor shaft. Pull out the sude of the brush that the belt goes on and put the belt on..
\015\012It might be a little tough going back in place because the belt will have a litlle tension..
Check your belt. Could be broken or loose.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums

The motor is running, the roller brush spinning rubber smell


The belt may be stretched replace it ... Vacuums

Electrolux nimble wont run only the roller brush


... Electrolux Vacuums

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN


Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?


Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC04 hello, my dyson seems to run ok in upright but when i tilt back the motor sounds like it is struggling, do you think it's down to the rollers being to low and can you adjust height of rollers to overcome said problem? yours chris


Hi.\015\012\015\012If the motor is struggling check to see how easy it is to rotate brush by hand it is stiff to rotate the bearings in the roller may be siezed or the roller could be clogged with hair etc check it & let me know what ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

The roller brushes do not rotate. The motor is running and the suction seems fine.


Are the brushes free of threads, lint, pet hair? If not, this can stop them from rotating. Check the outer edges near the wheel case as well. You can use tweezers to remove all the "tangler" stuff! I hope this helps. If it does, please rate my sugges ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.


Has this not got a rubber belt drive? ... Vacuums

Oreck XL2200: It turns on, the motor is running, the belt is on properly, but the roller brush is not moving


Quite often this is caused by either a broken or stretched belt, does not seem to be the problem here, or a frozen beater brush, the brush the belt drives.\015\012Remove the beater brush and clean as best you can. Spray a little WD40 between the bru ... Oreck XL2200 Bagged Upright Vacuum

My Hoover U6430-900: the motor seems to be running fine, the brushes turn fairly well, no blockages but no air is moving through it at all? Is it likely the fan and is this something I can replace myself?


Keep looking it must plugged somewhere ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Roller bar is not moving, sounds like motor is running


Remove the bottom plate underneath to expose the motor and bar AND belt. It sounds as though you have a broken belt. ... Vacuums

Brush roller wont turn, motor is good and the curcuit board appears fine. No evidence of anything blown or broken wires either.


Judging from this parts diagram:\012http://www. ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.


... Sebo Automatic X1 Bagged Upright Vacuum

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.


Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1154 seconds