Having problems with your Vacuums ?

Can't get the metal hose in flexitube to go back into top handle

Answers :

Try light greasing the top handle
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't get the metal hose in flexitube to go back into top handle

Try light greasing the top handle ... Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I pulled out the hose assembly from the back of the sweeper to clean it out. When I did so, there was a red/black wire that was attached to a small metal plate on the top of the assembly. What is the purpose of this? Does it need to be soldered back on?

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?

Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I am unable to get the handle off the top to use the hose. what to do?

Http://www.youtube.com/watch?v=Mm4rFq71zHA&feature=channelTake a look at this video ..at one point they show how to remove the hand ... Dyson Ball DC24 Bagless Upright Vacuum

The metal tube (wand) has come out of my DC14 handle and I can't get it back in. Any suggestions?

See if this manual helps you:\015\012\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

The hose provides suction when I remove the handle, however, I'm getting no suction from the brush when put back together?

Check for clog at the start of the suction port where brush roll is ... Dyson Ball DC24 Bagless Upright Vacuum

Clogged hose and can not get the handle off

The best way to fix this problem is to Stick the other end of the handle into the wall inlet making the nozzle contact the pin jacks of the wall inlet. You may need to work the clog back and forth by then plugging the hose in normally. Eventually you ... Electrolux Central Vacuum

I have a dyson DC07. The hose has come away from the hose end and the end is stuck in the top end of the wand as it sits in the upright position on the machine. Any ideas as how to get it out? If I can get it out it might just be a new hose. If not, it's a new hose and wand.t

... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have an Aerus lux 7000 and there is something stuck in the hose. I've tried prying it out with a hanger and only succeeded in getting it further down the hose. Is there a way to get the handle off of the hose?

DON'T try a coat hanger again it could tear the sidewall of the hose. Never push and obstruction in a vac You have a swivel handled hose. The handle will separate by removing several small screws buried under rubber buttons on the handle. The ... Vacuums

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.

I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

Cant get pin in kirby legend 11 handle,the main body seems to have shifted /

You will need mole grips to pull out handle pin. ... Kirby Heritage 2 and Legend Vacuum Cleaner Cord 32 ft Black, 192084

Broken black plastic of hose handle where it meets the metal part

You are going to have to contact the manufacture google the name and model # and serial # appliance parts places wont stock the specific part good luck . Tom ... Karcher K DS 5500 Vacuum

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?

Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?

If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

My handle won't go back up after an extended vacuuming session during which I used the hand/broom/animal hair attachments several times, thus pulling the hose out/putting it back in, starting/ stopping, and suddenly no matter what I do short of forcing it (and even if I try forcing it a bit) I can't raise the handle to put it away.

Do you know what model number Dyson you have? Is it the ball style one? Just find a similar product here on this page and let me know what model number is closest: ... Dyson Vacuums

I have an Electrolux Renaissance Vacuum C104H. How do I get take the hose off of the handle to install a new hose but keep the handle I have?

... Vacuums

I have a tear in the top of my hose. Right by the handle is there a way to shorten the hose a few inches at the top to repair the hole?

You'd be better off using duct tape on it. Ensure the wiring is intact first, then wrap a couple wraps of electrical tape around the hose, then 2-3 of duct tape. May not be pretty, but safer than cutting the hose and wiring just right to get everyt ... Kenmore 25512/ 25513 Progressive Canister Vacuum


Hi - greetings from Scotland!\015\012Im not sure if you mean telescopic hose = do you mean telescopic metal tubes? If so they are readily available on ebay.co.uk I buy from many sellers on there but Hoovermania are one of the best. \015\012\015 ... Philips Vacuums

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hose wont go back in place?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=34170&thid=375422\015\012Hose won’t go ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1134 seconds