Having problems with your Vacuums ?

The motor is running, the roller brush spinning rubber smell

\015 The motor is running, the roller brush is spinning, the belt isnt broken but there is a smell like rubber burning. and the suction isnt as strong... what should I check? there are no repair people where I live. thanks\015

Answers :

The belt may be stretched replace it
Sounds like the main suction pipe is blocked.
\015\012Unplug, and in good light - see if you can see any obstructions in the pipe from the prush area to the bag (in a bagless vacuum) or to the fan in a bag model.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor is running, the roller brush spinning rubber smell

The belt may be stretched replace it ... Vacuums

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??

... Oreck XL Ultra Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Roller brush won't spin (bissel 6390/3910 series)

I just fixed mine. It took me all of 10 minutes. Pull the brush out. Stand the brush on end on the edge of your study work bench/table top. while holding the brush vertical( on end) take a small phillips screwdriver and tap using a hammer on the meta ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Motor runs, brush won't turn, burning rubber smell


My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Motor bogged down, smelled rubber, brushes stopped turning

This repair would require motor replacement, based upon your explanation. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?

Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

The brush on my dc07 will not spin while vacuuming and it also smells of burnt rubber. I cleaned the brush bar and the belt is intact...

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt

... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!

That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

The brush does not spin but the belt is ok. The spindle at the inner end of the belt does not spin when the motor is running.

DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you are to refering to is the one from the bar to the brush. Unfortuenately the other belt is hidden un ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?

Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Electrolux nimble wont run only the roller brush

... Electrolux Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.

... Vacuums

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.

Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you

Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums

Motor runs, but noisey, smells hot, brushes don't turn

Joyce sounds like its time to look at the rollers they most likley have strings hair ect if tou know how to remove the roller you might want to get a pair of sissors and get to work what your smelling is the belt getting cloged with debre or all the ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Oreck XL2200: It turns on, the motor is running, the belt is on properly, but the roller brush is not moving

Quite often this is caused by either a broken or stretched belt, does not seem to be the problem here, or a frozen beater brush, the brush the belt drives.\015\012Remove the beater brush and clean as best you can. Spray a little WD40 between the bru ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0820 seconds