Having problems with your Vacuums ?


Answers :

All vacuum cleaners (upright) with a switch in the handle need to have all wiring disconnected.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


All vacuum cleaners (upright) with a switch in the handle need to have all wiring disconnected. ... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930

... Hoover Vacuums

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?

Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Removing handle of Hoover Widepath Floormate Spin-Scrub

... Vacuums

How to remove broken handle release on hoover windtunnel upright

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover Floormate Does anyone know how to remove the handle on the Hoover floormate? I need to repack and return it. Thanks

... Hoover Floormate H3000 Upright Wet/Dry Vacuum

How to remove handle HOOVER H3030 FloorMate Hard Floor Cleaner

... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover freejet 3-in-1 died, can't remove the handle to rebox

... Hoover H3045 Vacuum

How to remove the hoover windtunnel handle release lever

Tilt the handle back and pry it out with a flat blade screwdriver. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to remove handle from Hoover 5445-900 upright wind tunnel vacuum

Hoover.com doesn't have a manual specific to your model but there is one similar which will show how to remove the upper handle from the body.http://www.hoover.com/pdfs/manuals/U5467900.pdfDo you have a replacement switch? If ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

DM4470 001 Hoover Vacuum Cleaner. How do I remove the "Handle Release Pedal"

... Hoover Vacuums

I need to remove the handle from my Hoover Floormate. How to I do this?

These are not directions to specifically remove the handle, I looked for them and could not find them.\015\012At this URL you will see an exploded view of the unit. By looking at the exploded view you can see the screws that hold the handle in place ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

How do i remove the handle from a hoover floormate spinscrub hard floor cleaner, once it is on?

... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

How do you remove the handle on a Hoover floormate fh40010

... Hoover Vacuums

Remove & replace handle release lever on hoover model U6445, s/n 039900015686

From under the vacuum, there is a tab release that you need to pry out the old part. At this point, based on your serial nuimber, your vac is over 10 years old and may also need the base. The bracket is part of the base and not expensive, but the rep ... Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?

Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum

How to Remove Hoover Windtunnel Main Body

... Hoover S3639 WindTunnel Bagged Canister Vacuum

Handle on Dyson ball does not click back into position. This means that when you are hoovering the handle moves back and forth as you move the hoover instead of it being

... Vacuums

The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated

Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh

Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

Cant remove handle on dyson ball to use tools

Hi there,I'm sorry to hear you're having difficulties with your DC24. You might like to take a look at our online Support guide, which provides step-by-step instructions on using the hose, wand and accessories: ... Dyson Ball DC24 Bagless Upright Vacuum

Hoover U5465-900 Power Cord Replacement

Click here to see an exploded view of your vacuum. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0606 seconds