Having problems with your Vacuums ?

I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney


Answers :

You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney


You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious. ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

I'm trying to pull the fan drive of my vacuum so I can get to the motor but Ican not seem to get it off. I was wondering if there is a release switch or something that is preventing me from doing this. Also the motor seems to be burning but I think it's because ther is something in there clogging it up.


Check to see if it has reverse threads, Most do ... Vacuums

I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?


Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Brush not spinning , no belt is needing to be replaced, i think something in switch, cause before this problem the switch was always on , i would plug/unplug to turn it on. thisis case with 2 vacuums i have


... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Nutone model cv-350 vacuum motor will not shut off. I have to unplug system in garage. I disconnected wire to house vacuum inlets and motor is still running. There must be a reset on the motor. I have turned the external switch on and off and still no help.


Mine is the same, and it is the relay welding itself closed. The relay is switched by the low-voltage wiring that connects to the vacuum outlets, and it switches the motor on and off. Mine was welded in the energized position. I have cleaned and file ... Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

Brush spins, motor heats up, container doesn't spin anymore, not sure if it is "sucking up" anything ..had it for less than a year. Why won't it vacuum? dirt devil 12 amp HEPA filter vacuum


Probably clogged, or filters are very dirty ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

My Kenmore canaster vacuum Mod# 116.25513506 runs continously when plugged in regardless of the on/off hand controlled switch.. Disconnecting the switch located on the hose assembly has no affect of the continous vacuum operation. What component in the electric motor circuit is at fault and what would be the cost of repair?


... Kenmore Vacuums

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.


Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This


Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I have the Kenmore Model 116.36722600 Vacuum; while cleaning the carpets the vacuum all of the sudden stop working; I didn't smell anything burning; it was almost like someone unplugged it. I checked the rollers and I can move it forward and backwards with no problem. Do you think the motor just burned out? Does this vacuum have a fuse that I can reuse? I love this vacuum and would hate to toss it. thank you


... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1102 seconds