Having problems with your Vacuums ?

How to rewire a panasonic vacuum cleaner - Vacuums


Answers :

Once you have taken the handle off and the front plastic cover below the handle at the front and above the bag/bucket holder, you gain access into the power cable and switch connections.
\015\012One wire will disconnect easily, the other won't, so instead of trying take this wire out of its connection where many others are from the switch and the motor, cut it on the mains lead before it enters the connection and reconnect the new mains lead wire with a **** or block connector, the other should connect normally with a spade connecter,making sure its will take the amperage of the v/cleaner
\015\012Hope this makes sense!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to rewire a panasonic vacuum cleaner - Vacuums


Once you have taken the handle off and the front plastic cover below the handle at the front and above the bag/bucket holder, you gain access into the power cable and switch connections.\015\012One wire will disconnect easily, the ... Vacuums

Panasonic MC-UG729 vacuum cleaner overheats - Panasonic MC-UG729 Platinum Quiet Force Upright Vacuum Cleaner


... Panasonic MC-UG729 Platinum Quiet Force Upright Vacuum Cleaner

Panasonic vacuum cleaner overheats - Panasonic Vacuums


... Panasonic Vacuums

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915

Which Kenmore vacuum cleaners are made by Panasonic? Are all of their direct drive machines made by Panasonic? We have a blue Hoover Windtunnel with the dirt sensor. It cleans well, but it is unbelievably noisy. I wondered if something was out of place and the brushes were hitting, but everything looks normal. We bought Kenmore models 36722 and 36724 and love them. I believe they were made by Panasonic. Our Kirby sits in the basement. Much heavier. These are quiet and clean well. I would like an


Some Kenmore vacuums are made by Panasonic, some are made by Hoover or Eureka or even Sebo. I would go to a Panasonic dealer for that kind of machine instead of trying to go by the Kenmore brand. Sears has a hard time with service. A good Vacuum C ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Need part for panasonic vacuum cleaner mc-v5107.


... Vacuums

Panasonic MC-E468 vacuum cleaner manual


... Vacuums

Filters for panasonic vacuum cleaner MC-E468


Hi! Sometimes really hard to remember which of these models is which, so please forgive me if this is not a complete solution.  I'm pretty sure you will find there are two filters.  The first is a foam filter, and is located at the bottom o ... Panasonic Vacuums

Can I wash the filter of panasonic vacuum cleaner mc-cl481?


... Vacuums

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Service manual panasonic MC V9658 00 - Panasonic Motor for MC-V9658-00 Vacuum Cleaner


... Panasonic Motor for MC-V9658-00 Vacuum Cleaner

Dismantle mc-e735k vacuum cleaner - Panasonic Vacuums


... Panasonic Vacuums

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

Replace power lead on panasonic vacuum cleaner MCE 468


Generally, there are 'hidden' screws which are found under plastic plugs. Look for them. You may also find some screws on the opposite side of the plate holding the lead. Finally, sometimes the plate will slide up or down from its fixed position. ... Vacuums

How to change belt on Panasonic MC-E464 vacuum cleaner


Remove the bottom plate, the belt goes fron the brush rol to the motor shaft or pulley. ... Vacuums

My Panasonic vacuum cleaner MC-E461K has died.


... Panasonic Vacuums

My panasonic mce30001 vacuum cleaner starts but within i minute cuts out


... Vacuums

Where can I find a User Manual for a Panasonic Super Lightweight 1500W clean filtration MC-E464 vacuum cleaner?


... Panasonic Vacuums

How to fix Dirt Sensor on Panasonic vacuum cleaner


... Panasonic Mc-ul915 Bagless Upright Vacuum

Panasonic MC-E450 vacuum cleaner wiring connection access


Disconnect from power first!!Undo the three screws.Tap the base of the handle assembly from the front and it will slide back so it can be removedWith the handle removed, pivot up the bottom of the electrical box cover and it will un ... Panasonic Vacuums

Where can I find a new belt for my Panasonic vacuum cleaner model MC-E451?


Try www.part-smart.co.uk just send them a question or call them, they are the cheapest iv found ... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

How do I clean the dirt from inside the vacuum cleaner, brand name panasonic mce6003. I bought it without the manual and I cant get the dirt out from inside it since it is bagless. Please help :-(


... Panasonic MC-UG371 PLATINUM LINE Bagged Upright Vacuum

How do I change the power flex on a PANASONIC MC-E458 1200W vacuum cleaner. I cannot remove the cover to get to the end of the flex Thanks Bryan


... Vacuums

Panasonic vacuum cleaner MC E554


Wish you had listed your model number, they are all different you know, that wire you refer to I have seen on some models and it is only a belt guide. Should be a slot that it fits into. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0834 seconds