Having problems with your Vacuums ?
Putting the turbo head brushes back on to a dyson dc14 vaccum cle
\015 I bought a dyson dc14 however my husband through the instructions out in the recycle. I need to know how to put the brush bit back in after cleaning it of dog hair and human hair. thanks\015
Congratulations on owning a great vacuum cleaner, it's just like mine! Here's what I do: Grab the drive belt and pull while you wiggle the brush bar into it. You have to get a little bit physical with it. The ends of the brush bar will nestle into their keeper pockets nicely when you've got it right. Good luck!
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Putting the turbo head brushes back on to a dyson dc14 vaccum cle
Congratulations on owning a great vacuum cleaner, it's just like mine! Here's what I do: Grab the drive belt and pull while you wiggle the brush bar into it. You have to get a little bit physical with it. The ends of the brush bar will nestle int ... Vacuums
Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.
You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
LittleGreen Machine Pro turbo brush put back together
Here is the web site with the parts breakdown.\015\012http://www.marbeck.com/carpetcleaner_parts_bissell.html ... Bissell Vacuums
Dyson dc14 putting back together - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
How to put the brush back in to the turquoise dyson dc07 and put the belt back on
... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum
I removed the handle of my Dyson DC24 to vaccum in high areas and now when i try to put the back piece back, it doesn't click. So when try to vaccum on the floor the handle just comes off.
Hi there,I'm sorry to hear you're having difficulty with your DC24. The wand handle should reattach easily to the machine, locking into place with an audible 'click'. If it doesn't seem to be doing this, you may want to check you have the han ... Dyson Ball DC24 Bagless Upright Vacuum
How can i put the forward lock back into my dyson dc14 animal?
Hi there,I'm sorry to hear you've experienced this issue with your DC14. I'd encourage you to get in touch with us directly, as we'd appreciate the opportunity to provide further assistance.You can call us on 0800 298 0298 (UK), or 1 ... Dyson Vacuums
The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!
Great. ... Kenmore Vacuums
Brush stopped turning on my animal dyson-only 3 weeks old. I already took off the brush and put it back on
Brush stopped turning on my dc07 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?
If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum
Dyson DC14 Brush Bar won't turn
You don't need to take it for repairs, I just corrected the same problem on the phone with a tech. Have the head on your lap, make sure the end nearest the little belt has the rounded side of the bar facing you. The squared off end faces towards th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Dyson DC28 works fine for a minute then it's like if the brush head gets too much resistance it quits spinning and the light starts flashing. When I turn the vacumn off then back on it's f
Hi Gayle,I'm sorry to hear you're having difficulties with your DC28. From what you've described, it sounds as if you may have the brushbar set at a level too low for the type of carpeting you're cleaning. If you select a higher carpet settin ... Dyson DC28 Animal Bagless Upright Vacuum
I have a hoover celebrity QS wuith the power head. I have only used the powerhead for years purchased in 75) I removed the powerhead to use the brush and the power does not come on but if I put the powerhead back on it works again.
You have done very well keeping this appliance working since 1975!!!\015\012Lucky you!\015\012I'm not certain you would be able to get replacement parts for this model any longer,\015\012Maybe you will just have to continue with the ... Hoover Vacuums
The upright lock and spring have fallen out of my dyson dc14 vacuum. i need to find out where to put it back in as the part seems to be complete.
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Having trouble putting brush roller back together on riccar vaccum
... Riccar 8955 Upright Vacuum
I have a Turbo Z V-CP744NB Vaccum cleaner which is discontinued. I am unable to put the bag back in the canister properly and need some guidance
I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help
Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums
How to clean turbo brush of harmony electrolux and put it back together properly
Wait, there are two more screws that must be removed before the top shell will come off. They are located under the wheels. Pop the wheels out by simply inserting yoru finger or a small tool into the wheel and pulling straight up. Remove those two ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum
Can you show how to put the pet turbo brush back together?
... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.
Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Dyson dc14 How do we replace the belt one I removed it to clean hair from brushes? Can't get it back in place. Any tricks or suggestions. Craig Dittmar
Hi am i right to assume the belt is still in place ie in position around the drive wheel of motor? and you have removed the roller/brush only? and you now have difficulty re assembling the belt on brush and relocating brush into its holder ?? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?
... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Ive put a new roller brush in my dyson dc14 now it makes a awful noise
Hi There, I work as a tech for VacuumSpot and the problem you are describing is pretty common. It generally happens when you replace the belt or roller as the new one isn' ... Vacuums
Putting the roller brush back in - Dyson DC33 Bagged Upright Vacuum
... Dyson DC33 Bagged Upright Vacuum