Having problems with your Vacuums ?

My dirt devil ultra vision has NO suction on the hose and the thing practically eats belts. What could the problem be?


Answers :

First of all, if it eats belts, the brush roll bearings have going - change the brush roll.
\015\012Second, check your filters and for blockages
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dirt devil ultra vision has NO suction on the hose and the thing practically eats belts. What could the problem be?


First of all, if it eats belts, the brush roll bearings have going - change the brush roll.\015\012Second, check your filters and for blockages ... Vacuums

Dirt devil ultra vision turbo suction problem


... Vacuums

Hi I have a dirt devil vision. Hose works, but does not vacuuming the floor. Belts are not broken. Larger belt is moving, smaller belt that moves the brushes does not.


Hi krueger, sorry for the problems but hers an idea how about turning on the vacuum and put your hand under the part where it sucks uo the dirt off the floor and i guessing you would have a little suction, since the brushes are not moving its going t ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Sebo Air Belt C3.1 Were hose enters handle, leaks air causing a high pitched whistling sound. How can I fix this. I have taken hose into shop, but they could not find a problem.


... Sebo Air Belt C3.1 Bagged Canister Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

I have a dirt devil ultra vision turbo, it lost suction. took it apart blew it out with the air hose, I think we put the bottom plate on wrong but can't figure out how it goes, it is blowing dirt out but the suction hose works.


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My Eureka Maxima 4704 pink vacuum is really squalling .. its so loud you need ear plugs .. we just got the thing Christmas .. and has been used under normal conditions..we keep the filter clean and even recently washed it and let it dry for 12 hrs to see if that was the problem but it wasn't what else could be the problem ... I do not think that the belt is slipping because I can't smell rubber burning ...IM STUMPED


... Vacuums

The belt is intact but the aggitator doesn't spin anymore. Had a horrible rubber smell, went to change belt. Not the problem. Anyone know what could be wrong? Dirt Devil bagless w/dirt indicator


It could also be a bearing problem in the roller brush. Take the belt\015\012off of the roller brush and see if the brush spins freely, if not, remove the\015\012roller brush and check both ends to see if one end is stuck. If so you ... Vacuums

My dirt devil ultra vision is making a loud noise when turned on. I replaced the belt and cleaned the filters and the noise is still there.


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Dirt devil ultra vision cyclonic vacum dose not have suction , cleaned filter and hoses still no suction what can i do


... Dirt Devil M08100RT Classic Handheld Vacuum

How do you replace the belt on a Dirt Devil UD70010 Ultra Vision vacuum


... Dirt Devil UD70010RM RFB

WE HAVE A DIRT DEVIL ULTRA VISION TURBO VACUUM MOD 87800 AND ITS BREAKING BELTS AND THE MOTOR SMELLS WHEN WE RUN IT


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a dirt devil ultra vision turbo that is sucking up properly but it is blowing dust out instead of clean air. Is this a problem with my filter? Somehow it is bypassing it.


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I don't know how to change the belt on the dirt devil ultra vision no manual


Take all the screws off the bottom to access the beater bar than slide out (belt will also be right there ) just slide a new one on...... ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?


Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Dirt devil ultra vision turbo; how to remove hose from base


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

The dirt devil vision wide glide Model 086700W appears to have no suction. I have cleaned the hoses and filter and still there is nothing being picked up. Also, I have checked the belt.


There must be a blockage after the hose, check where the hose plugs into the vacuum. make sure unit is un plugged for safety ... Vacuums

How do I change the belt on a dirt devil ultra vision vacuum cleaner


I just changed mine and I will be blunt. First off, the design is **** on this vacume, secondly the belt was designed to break on the rusty carbon steel pully rod. Ok now that I've vented we will get down to business. On the bottom of the vacume y ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My Hoover upright vacuum has gotten very loud. I have checked the roller, belts and hoses but I haven't found anything. What could the problem be? thanks


Most Hoover uprights are a "fan first" design, meaning that all dirt enters the motor , hits an impeller fan and is blown from there into the bag. You will need to open the vac, remove the belt and two C shaped clamps holding the motor in place and ... Vacuums

Dirt devil ultra vision turbo model #087300


I was having the same issue with my Dirt Devil. I noticed when attempting to use the hose that there was little to no suction. I unscrewed the hose mount from the back and completely removed the hose. I spent a good 10 minutes stretching out and shak ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My Dirt Devil ultra vision will not **** from base


Your belt is probably worn or broken. You need to replace the belt if you haven't recently. You can get the belts you need here:Dirt Devil Ultra V ... Vacuums

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

Dyson animal won't start. Never had any problem with this vacuum. No apparent problem. No electrical problem with house or outlet. If there are some common things I could check/fix, things that might go wrong, I would like to check them out and get this machine going again.


Hi there, if the machine was running and cut out in use, this could be due to the motor overheating. The cause of this would be a blockage or a dirty filter. These checks can be found in the Support section on our website at www.dyson.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0838 seconds