Having problems with your Vacuums ?

How to check if a belt is broken? - Vacuums

Answers :

With hoover off, tip backwards, and feel the beater brush roller. Try to rotate it. If it is stiff, the belt is ok. If it moves very easily - you need a new belt.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The roller on my Dyson vacuum has stopped rotating (I still have suction) I have checked the belt (not Broken) and have checked and cleaned the roller and spindle and also checked the "auto" button setting on the vacuum but to no avail ... Anybody have any clue as to the problem Many thanks

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

The suction still works but the primary floor vacuum doesn't. I checked the belt and its not broken. The engine that runs the floor vacuum doesn't engage like it used to

The belt doesn't have to be broken to affect the the way the vacuum picks up on carpet. If the belt is stretched then it will slip and not turn the roller brush properly. Here is the manual and belts you need: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help

I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

How to check if a belt is broken? - Vacuums

With hoover off, tip backwards, and feel the beater brush roller. Try to rotate it. If it is stiff, the belt is ok. If it moves very easily - you need a new belt. ... Vacuums

No suction My dirt devil featherlight vacuum has no suction. I have checked all hoses and they are clear. I did replace the belt which had broken and since I did that the suction is gone.

Take the cone filter out of the dirt cup and start it up if you have suction the filter is the problem,if still no suction the you have a clogged hose or a clogged intake hose which is at the bottom it will be a clear hose coming up the backside fro ... Dirt Devil Featherlight Bagless Upright Vacuum

My kenmore progressive canister vacuum's power head has stopped working. When I check for suction from the hose, it seems strong. Could it be a belt has broken? Is this a repair that I could do myself? Thank you!

... Kenmore Vacuums

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum

This video shows you everything you need to know ... Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Broken belt My husband and i took apart the vacuum and found out the belt was broken. how do you replace it? we could not remove the area where the belt is.

Hi.\015\012\015\012If you cant easily see how to replace the Belt then I think your Dc07 has A clutch unit.\015\012\015\012This type of Dc07 has 2 belts one from motor to clutch & the second belt goes clutch to brush rolle ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is

Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.

You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

The vacuum i've had for 6 months has very liittle suction power. checked that the belt is on. cleaned filter. checked to see if hoses were clogged. I used a super vac to suction any debris out of vacuum. still little suction power

As this unit has 3 filters on it, a lot of people forget about the one filter that will cause all of your trouble here. \012\012There is the exhaust hepa filter, no problem, your unit is pretty new, it shouldn't be a problem. \012Th ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

Belt for Hoover Powermax S3606 Canister Vacuum is Broken

Your belt number will be listed on the data label with the model number. Check your local Hoover / Dirt devil dealer for the part. ... Hoover S3606 Bagged Canister Vacuum

Hoover Upright...OLD vacuum, broken belt

The rod must be your brush roll. it should just pull out, Have you removed the cover over the brush roll? When you do get the brush roll out, turnb the ends and make sure they turn freely, if nit, replace it also. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi I have a dirt devil vision. Hose works, but does not vacuuming the floor. Belts are not broken. Larger belt is moving, smaller belt that moves the brushes does not.

Hi krueger, sorry for the problems but hers an idea how about turning on the vacuum and put your hand under the part where it sucks uo the dirt off the floor and i guessing you would have a little suction, since the brushes are not moving its going t ... Dirt Devil M086700 Vision Bagless Upright Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

I have the Miele S175i Powerhouse Plus and it vacuums fine, but the bottom piece of the vacuum is broken. The head of the vacuum swivels freely and doesn't lock into place. Also, the connecting belt is messed up. How can I fix the head so that it doesn't swivel freely?

... Miele S175i Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0970 seconds