Having problems with your Vacuums ?

It has a high whining sound when operating replaced all the filters and the belt when i removed the motor and ran it by itself there is no whining sound

Answers :

\015\012 You may have an obstruction somewhere in the hose or body... could be a quick fix for you.
\015\012Hope this helps... Good luck!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It has a high whining sound when operating replaced all the filters and the belt when i removed the motor and ran it by itself there is no whining sound

Hi,\015\012 You may have an obstruction somewhere in the hose or body... could be a quick fix for you.\015\012Hope this helps... Good luck! ... Vacuums

Oreck XL Commercial vacuum cleaner ---- has high pitch squeal or whining sound when turned on. The belt is ok and the suction is ok. Is the motor about to go out?

... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

Loud noise I ran over a string and then shut it off quickly. It now makes a horrible grinding sound. Did I ruin the motor? Sounds like something came undone. I checked the belt and that is fine. Ideas?

I think you damaged the belt. I ran over a sock once and it made a grinding noise but still worked for several months after the incident. Finally, the belt broke off. I had it replaced and now it doesn't make that sound. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?

Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

I have a Nutone CV-450. When the unit is turned on the motor makes a high pitched whining sound. The suction seems like it is reduced and there is a burning rubber smell coming from the unit. Suction at the unit itself is also reduced. Any ideas about the cause of the problem and the solution?

... Broan-NuTone CV450 Central Bagged Central System Vacuum

My shop vac is plugged. The hose is clear. The filter is removed. The filter bag is not installed. It still won't draw a suction. It sounds like it is plugged. The motor whines at a higher-than-usual pitch. What can I do?

Turn off the vac, take the head off of it and remove the filter paper. Inside, there's a white ball (bigger than golf ball, smaller than baseball) that's inside a cage. This is designed to keep water out of the blower when the vac tips over, and sh ... Vacuums

No suction. filter and hose clear. motor high pitch. don't know how to remove cover to check motor.

Something is clogged somewhere start from bottom and foolow suction path all the way through. wht kind of vacuum? ... Vacuums

Bissell lift-off revolution, motor gets hot, loud whining sound

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Not working  I hit the switch and there is no sound of a motor.  Nothing is happening.  It was working seconds earlier and suddenly it stopped.  The plug was in and I replugged it into the outlet.  Still, no power and no motor sound. Does this happen if the belt goes? Thank you, Jill

If it was just a broken belt you would still hear the motor running. most likely its in your cord or switch. check the main cord, connections to the switch, and also the motor supply cord that goes from the handle to the vacuum head. ... Oreck XL Ultra Bagged Upright Vacuum

There seems to been a high pitched sound in the motor. I'd describe it as a 'dry' sound, and the high pitch of it is very loud. I want to stop vacuuming because it's so loud. Are there any oil/greasing points/spots? If so, how do I find them?

High pitched noise is not good. It may indicate that a bearing is going out. I would not use Kirby as it may lead to burned motor.If you feel that it vibrates quite a bit too - then it may be only broken fan blade.Fan blade - ... Kirby Generation 3 Bagged Upright Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

It sounds as though a belt is rubbing or slightly off-track. The sound is extremely loud. We've removed the plate around the brush bar, made sure the brushes are free of dog hair, and found that the belt appears to be on track. What should we try now? We haven't tried to use it to check for suction for fear of doing real damage! Thank you. Marcia VanDyne

Is the sound coming from the head unit where the belt is attached? When you power up the vac, can you watch the belt to see if it is frayed or running off track. I have the same Dyson and had this same issue, cleaning the head cured it, but your issu ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Belt replacement appears to have 2 belts, 1 is on and 1 is missing, the belt that is driven by the motor is missing, how do I remove the clutch housing where the belt goes?

Hi.\015\012\015\012You are correct there are 2 belts.\015\012They can be tricky to replace most shops will state they cant be replaced & you require new clutch.\015\012So try this site ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The motor in my Powermate (Kenmore Canister 116.27614700) is whining, high pitched, but still works. A local shop told me the motor is dying (the one in the Powermate that drives the beater bar) and would cost $150 for them to repair. The machine is only 1.5 years old and I paid $300...yikes. I think I can fix it but don't understand why the foam gasket that apparently wraps around the motor costs as much as the motor. This is assuming that part 32 (ks747156) is the foam I see glued to my cur

I think you are right! Buy the motor.....use the gasket from the old motor if you can cut it off clean and just glue it on the new one.\015\012\015\012The connectors are just brass blade connectors which you should be able to get at a Ho ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Motor whined loudly. Vacuum failure. Suspect motor failure. Hoover.com doesn't list a replacement motor. Drive also failed - could be secondary belt HOOVER U6323- Power Drive Bagged Upright Regards, Jeffrey

Hello, funI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

How do I gain access to the motor of an Electrolux 2000 canister vacuum. The air intake on the motor must be partially blocked as there is a loss of suction and the motor makes that high pitched whine like it does when you cover the hose with your hand

Dismantling the vacuum probably won't help much, and reassembling can be a bear. \015\012To check the intake, remove bag and look into bottom of bag well. It there's a filter there, remove it and check intake at bottom of bag well. Clear if t ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?

... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0936 seconds