Having problems with your Vacuums ?
The hose keeps pulling out of machine and now power head is not working.
What kind of machine, make sure you lock it into place
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The hose keeps pulling out of machine and now power head is not working.
What kind of machine, make sure you lock it into place ... Vacuums
The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!
Great. ... Kenmore Vacuums
My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.
It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea
Beam solaire hose only works to suction The power head isn't working. Have another hose and the power head does work on that one so I know it is the hose
The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?
Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum
I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working
We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum
The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?
Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson
Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto
Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums
I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.
Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Dyson dc05 power head not working. Fitted new hose and power head
Please go to http://www.dyson.com/support/help.asp?article=32&product=DC22-MOTORHEAD-USplease select the model exactly, and proceed with common sense for troubleshooting problem and fix it.You must shure to see the videos, and see if the ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Model 116.27914 power mate connection to lower wand is loose. Head unit works when pushing forward putting downward pressure on it, but looses power when you pull back on unit and connection is lost.
... Kenmore Vacuums
My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab
(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum
My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett
I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums
Vacuum Problem My dirt devil vacuum is losing suction and keeps clogging. All the dirt keeps sticking to the screen by the filter and then it would stop working. Also the hose does not have a strong suction power either. So what can I do?
The Bissell can have several filters in it, depending on the model. Some have a round hepa filter that is covered with a foam sleeve. This filter is located at the bottom of the dirt cup. Others have a foam filter that is located under the dirt cup i ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
I have an electrolux cyclonic vacuum and turbo head wont work properly keeps losing power ?
We have an Epic6500. when we plug it in the machine works without the hose. We even purchased a new hose thinking there was a problem with the hose. However as soon as we put the hose on the machine the machine does not work. What do you think the problem may be?
Wow, this is a good one. I wonder if anyone has wrked on this machine before. Do you remember what happened when it stopped working / Obviously there is a foul up in the wiring. I need more info. When the machine is on does it shut off as soon as the ... Electrolux Epic 6500 Vacuum
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
My kenmore progressive canister vacuum's power head has stopped working. When I check for suction from the hose, it seems strong. Could it be a belt has broken? Is this a repair that I could do myself? Thank you!
... Kenmore Vacuums
Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin
... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
The Delta power head is not working. Brush is not turning.
... Electrolux EL6989A Bagged Canister Vacuum
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
Power head not working
There is a gray button next to the red "power on" button that powers the brush unit. If the unit has tripped the reset for some reason it must be reset. This can be done by holding the gray button down for ten seconds while the unit is not running. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The power head on my kenmore 22822 Canister Vacuum won't work? the power upholstery head works fine.
I have the kenmore whisper belt and i have a reset button on mine ... Kenmore 22822 Canister Vacuum
I recently lost power to the power head. Thinking the hose was not sending current to the head, I bought a new hose. It did not solve my problem. I have since noticed that a warning symbel is appearing that indicates what looks like a key with TA inside. The vacumn has good suction. Please advise John.
Hi\015\012\015\012Please check the link bellow to diagnose your problem…..\015\012\015\012http://home.howstuffw ... Electrolux Epic 6500 Vacuum