Having problems with your Vacuums ?

Can,t make my rewind cord-rewind --How do you take the back off???????.SOOOOO------I can check the problem----need respond ASAP!!!!!!!!

Answers :

This is a tricky job and will require a new winder mechanism. Take it to a repair shop and ask for a quote.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can,t make my rewind cord-rewind --How do you take the back off???????.SOOOOO------I can check the problem----need respond ASAP!!!!!!!!

This is a tricky job and will require a new winder mechanism. Take it to a repair shop and ask for a quote. ... Vacuums

I need to get into it to check what the problem

Hi, It is either the motor brushes and or the armature. My advice would be to buy a new cleaner, cheaper in the long run. ... Electrolux Z7108 Canister Vacuum

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

This is BS i want someone to respond to my ? onthe manual for the SC630-FS there should be one in the box. so, i need an answer ASAP

... Vacuums

Hi all, I have a Janome 234D overlocker and when I try to sew with it, it misses stitches. What could be causing this problem and how do I fix it? I tried rethreading,checked the tension and stitch length dials on the side and I dont have a manual for any instructions, help is desperately needed, regards Wendy

... Vacuums

92L3-W this unit was fine when new, did a good job, after a few months it got very loud. it is so loud you need ear plugs to use it. i have checked and cleaned it. there is'nt any visible problem with it. after cleaning and changing all filters it still is very loud a lot more than when it was new.

... Bissell Vacuums

My hoover elite rewind does not pick up dirt like it should. how do i check for a clog? I can hear it picking stuff up but when I empty the cannister there isn't much in it. today it shut off like it threw a breaker. I let it sit and plugged it back in and it started working again. don't know if the problems are related or not. any suggestions??

Have you cleaned the inside filter? Open the cup hold on to the yellow piece in the center and twist it to unlock (there are arrows on the pieces to show how far to twist). Take the filter out and try to clean as much of the debris off of it. ... Vacuums

I have a kirby G7D ultamite, I recently replaced the switch, it worked for two weeks then it hasnt turned on since. Also I checked the cord, it has power going to it. Please respond asap thank you.

The switch has probably come lose, have you checked the motor to make sure it is good? Usually the cord will short out right by the motor assembly try to wiggle it while plugged in and see what it does, its most likely the cord I recondition kirbys a ... Vacuums

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

Ok so, here's my problem. I have a nintendo DSi and I'm trying to connect it to the internet. I've been searching on google on how to connect it. They said that i need wi-fi and some say I don't need wi-fi and some are saying i need a wirelerr router and some are saying that I don't need a wireless router. I'm wondering how I should connect my DSi without a wireless router and without wi-fi.

Http://www.nintendodsi.com/meet-dsi-xl.jspI think you are trying to do the impossible but try this site. ... Vacuums

Need to check , belt , donot where to check,on

You can get hoover replacement belts and manuals here:Hoover Vacuum Belts ... Vacuums

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.

Squealing ... Vacuums

The roller on my Dyson vacuum has stopped rotating (I still have suction) I have checked the belt (not Broken) and have checked and cleaned the roller and spindle and also checked the "auto" button setting on the vacuum but to no avail ... Anybody have any clue as to the problem Many thanks

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson animal won't start. Never had any problem with this vacuum. No apparent problem. No electrical problem with house or outlet. If there are some common things I could check/fix, things that might go wrong, I would like to check them out and get this machine going again.

Hi there, if the machine was running and cut out in use, this could be due to the motor overheating. The cause of this would be a blockage or a dirty filter. These checks can be found in the Support section on our website at www.dyson.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Low suction Replacing filters....need help replacing the belt - anyone know how? But before doing these things, have had a problem with suction....I'll let you know if the problem clears up.

Hi, You can take care of both things at once. Here's how:\015\012Unplug and flip your vacuum over, beater bar side up. Remove the cover base plate that surrounds your beater bar. It's held on with either clips or screws, and usually "hinges ... Eureka 2961AVZ Bagless Upright Vacuum

Orange light is on - bag/hose check and I can't figure out why. Bag is not full. What do I need to check on the hose?

May be plugged ... Vacuums

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.

You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.

The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

My Kirby G5 has a power problem. Its handle needs to be tiltled all the way to almost flat position for the power to comne on. If the handle is back up to its standing postion, the power will be off. What's the cause of this problem? Any suggestions/comments will be greatly appreciated!!!

Sounds like u may have a problem with the cord connection inside the power plant would suggest u take to repair shop not something i would suggest u try yourself ... Kirby G5 Bagged Upright Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

Need instruction/care booklet for my Bissell powerforce vaccum model #3522-5. Bacfk of vaccum hose is filled with dirt and when attachment is used, dust & dirt fly everywhere. I don't have the care booklet for the vaccum and need to figure out how to fix the problem. Thanks

... Bissell 3522 PowerForce Bagged Upright Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?

Hi!  Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem.  You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one.  If your Henry ... Numatic Henry Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0847 seconds