Having problems with your Vacuums ?

Hoover model u5076-930 I can't get into the motor to replace the belt. I don't see are screws

Answers :

I don't recognize this model # but most Hoover products have the screws usually silver at the bottom underside of the carpet head. They will also have two additional screwdriver slots mid way along the side of the head on some models.
When replacing the belt use a genuine Hoover belt by model #. It will be snug. Also clean out the hair and thread underneath the caps at the end of the brush and be sure the brush turns freely with belt off.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover model u5076-930 I can't get into the motor to replace the belt. I don't see are screws

I don't recognize this model # but most Hoover products have the screws usually silver at the bottom underside of the carpet head. They will also have two additional screwdriver slots mid way along the side of the head on some models. When repl ... Vacuums

Hoover model U5076-930 I can't get in to replace the belt. I can see no screws

Please look at this manual:\015\012http://www.hoover.com/pdfs/manuals/U5046930.pdf\015\012\015\012Page #12 shows belt replacement. ... Hoover Turbopower Dual U5076 Vacuum

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940

You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.

... Vacuums

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!

Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

I have a Dirt Devil Featherlite Model 085430. It making a horrible noise and I want to open it up to see if anything is broken or lodged in the motor housing. I've removed all the screws I can find and still can't get the thing apart.

Hi,\015\012\015\012The user manuals in this site may be helpful.\015\012\015\012Best wishes. ... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.

... Eureka Sanitaire S661 Bagged Upright Vacuum

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based

... Bissell Vacuums

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole

Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

Replacement motor I am undertaking the repair of an old dustbuster as a training exercise. ,The motor in my V2410 is Made by Johnson Electric but I cannot find reference to the numbers marked on it on the manufacturers website. Are you able to give me a model number for an equivalent replacement or the specifications of the original motor? Thanks, Gary.

... Black & Decker V2410 DustBuster Handheld Vacuum

How to replace the motor brushes? When should the motor brushes be replaced? Where can I purchase motor brushes for Model 1500 Easy-flow?

... Easy Flo EF1500 Vacuum

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman

Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums

I have hoover steamvac models f5889-900 and f7222-900. The brush motor is broken in model f7222-900 and I replace with working motor in f5889-900? I am using f5889-900 just as parts

... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus

... Bissell 6595 Lift Off Bagless Upright Vacuum

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.

If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

ELECTROLUX model 1623 switch replace

Hi jjda..slide the strips/bumper...maybe it's hard to slide off...but try again...this week-end i open my 1623 too...no screws..just the strips hold the top and the base together..good luck!...Joel ... Electrolux Vacuums

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.

If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky

Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0805 seconds