Having problems with your Vacuums ?

Shark v1510 How do I replace the belt?

\015 The brush head doesn't spin. I assume that there is a broken belt somewhere. shark v1510 How do I replace the belt?\015

Answers :

Remove the outside sliding cover... remove 2 screw in from of housing, and also the screw holding the wheel on the brush head cap side of the housing. Once screws are rmoved, you can remove brush head cap and belt cover. Pull down on belt cover to remove. It is held by screw crossing the top of the cover from the side. Belts are hard to find, but can be ordered from shark web site (2) for 7.95 and shipping.

I had the same problem. Some one should stock these belts in the states, because Shark outsources thier call center to India, which sucks. It took 20 minutes on the phone to communicate through the noise and language barrier just to order a belt!


Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shark v1510 How do I replace the belt?


Remove the outside sliding cover... remove 2 screw in from of housing, and also the screw holding the wheel on the brush head cap side of the housing. Once screws are rmoved, you can remove brush head cap and belt cover. Pull down on belt cover to r ... Vacuums

How do I get the beater brush off of the vacumm to replace the belt? The vacumm is a Shark roadstar . I can get the belt on the one end but I cannot get the brush up to put it on that end. Judy It is a Shark Roadstar EURO-PRO Model No. UV208C


... Vacuums

I have the same rproblem with my little Shark V15Z hand held vacuum. the belt broke,there's no instruction on how to replace (and apparenlty it was not designed to be replaced (at least with out a lot of research). I see BElectric describes how to find the hidden path, but now where can we buy the correct belts??


... Euro-Pro HEPA Shark EP035 Bagless Handheld Vacuum

Can't find a site to order a replacement belt for my Shark model V15Z which I bought for our motor home. It was used very little before the belt broke. I will be trashing this vacuum, and will NEVER buy another Shark product.


This web site has the belt for V15Z http://www.appliancefactoryparts.com/vacuumcleaners/brands/shark/v15z.html I found this one works great Pain to get belt on but not a problem since then. http://www.totalvac.com/ROR-1040.html (Dirt Devil type 1 Bel ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

How do i replace belt on shark v15z


... Euro-Pro Vacuums

Replacing drive belt on shark hand vac v15z - Euro-Pro Shark EP750 Bagless Handheld Vacuum


... Euro-Pro Shark EP750 Bagless Handheld Vacuum

Replace belt on a shark - Shark Navigator Bagless Upright Vacuum


... Shark Navigator Bagless Upright Vacuum

Replace brush belt on shark navigator nv350 - Shark Navigator Lift-Away NV350


... Shark Navigator Lift-Away NV350

I need a replacement belt for a V1315 Shark Roadster Vacuum cleaner. Looks like there's no way to get one. Is there a compatible belt that will fit this vacuum?


... Euro-Pro Roadster V1315 Upright Vacuum

I need to replace a belt on the shark infinity pet care system upright vacuum. I have the belt I need a manual to show me how to put it on


... Euro-Pro NV31 Infinity Vacuum

How to replace belt of shark vacuum cleaner moder uv 308 show on you tube


... Vacuums

How to get cover off to replace belt on Navigator Shark vacuum


... Euro-Pro EuroPro Shark Navigator Vacuum

The belt broke, and I can't find out how to get a replacement (Shark Hand Held Euro-Pro Model V15Z. Help!


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Replace belts shark v1420gb - Vacuums


... Vacuums

I need to replace belt on shark uv208 vac how do i do this


... Euro-Pro UV209 Upright Vacuum

No suction and overheating - Euro-Pro Shark Hand Vac Belt Models FM430/K/H, V1510


... Euro-Pro Shark Hand Vac Belt Models FM430/K/H, V1510

Where can I get Shark NV 352 replacement belt


Try bed bath and beyond or the official shark website ... Shark Navigator Lift-Away NV350

Shark navigator belt replacement


... Euro-Pro EuroPro Shark Navigator Vacuum

How can I replace the belt on my "Shark" carpet sweeper?


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.


Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey


... Electrolux Vacuums

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0498 seconds