Having problems with your Vacuums ?

My dyson 25 animal has lost suction from the floor portion of the machine. All the hot hair is coming off the front bottom part, by the ball. Its as if the connection of air has been disconnected. The attachment works fine, though.

Answers :

You have a serious clog that must be removed. It is somewhere between the floor and the bag or where ever the dirt goes. Clear it and you will be back in business.
\015\012Thanks for using fixya.com
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson 25 animal has lost suction from the floor portion of the machine. All the hot hair is coming off the front bottom part, by the ball. Its as if the connection of air has been disconnected. The attachment works fine, though.

You have a serious clog that must be removed. It is somewhere between the floor and the bag or where ever the dirt goes. Clear it and you will be back in business.\015\012\015\012Thanks for using fixya.com ... Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.

Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.

I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto

Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?

Open this manual to page 18 and clean all the filters listed to restore air flow.http://www.managemylife.com/mmh/lis_pdf/OWNM/L0908343.pdf ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?

You have the answer and just don't know it. You are there so keep looking. Somewhere between where the suction hose connects with the lower hose and the power-head. There is a blockage, you may need to turn the unit upside down and look there or try ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Model, 116.c85pbpk0v022 Power-Mate Jr. attachment stopped working, could it be a part within the unit (i.e. the electrical component) or do I need to replace the unit? How do I troubleshoot the electrical connection? No known drop or abuse. Worked last time I used it.

This model frequently stops because, lint, hair, etc. gets caught between the two end pieces of the brush cylinder. Do the following to fix it:1) Remove the two Philips screws from the underside of the unit. 2) The side with the tag will ... Kenmore Vacuums

My dyson 07 doesnt **** up when im doing the carpet but the hose works fine? when im vacuming it sucks up very little and the hose part seems to be sucking up air when im doing the carpet? would this mean something is plug??? thanks randy

There is a block in the hose take lower hose of and clean ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!

The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover windtunnel bagless vac that is several years old. the floor vacuum part still works fine, but the handtool attachment has no suction and is useless all of a sudden.

Don't have your model number, but some have a valve down on the noozle part that may be broke. When it is its upright position, the valve won't change over to the hose only position. You would have to remove the top cover to see this. ... Vacuums

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.

May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Carpet attachment attachment appears to have poor/intermittent connection. When initiated, it works for <30 seconds before shutting down. Suction still works but carpet attachment doesn't. Near impossible to restart.

Mine became intermittant so I took apart the exteding wand section. I found that power is transmitted to the cleaning head through a ribbon cable which was damaged (burnt) from repeatedly adjusting the length of the wand. A new wand correct the probl ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My progressive brush motor only works when I've got it twisted to the right, and then not always. Obviously a bad connection. The female part of the connection at the handle is blackened. Is this something we can repair/replace ourselves, and if so, how? which parts do we need

\012I will give you the easiest way I think you van solve this. What I would do is take the wand down to my local used vacuum store and show them the piece with the black on it. If they agree that it should be ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.

Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.

... Vacuums

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!

Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

No water/soap to carpet, but upholstery attachment works fine.

If the hose is spraying, then the pump is working. The pump is a common problem which is why the repair shop assumes that it is the problem, but their repair cost is way out of line. The more likely cause could be the heater. The heaters on these mac ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0959 seconds