Having problems with your Vacuums ?

How do i replace the power switch on a DC04? I can't get to the switch, are there any special tricks to open the swich module?

Answers :

Yes there is a trick it you look at the switch cover at the edge nearest to the handle you will see a little groove down inside it is the clip that holds the cover on it iis part of the the switch cover and it is hard to remove without breaking it,you will need somthing small enough to go down the hole about one and a half inches the tool will need to have 90 degree bend in it you need to put the unit in the on position unplugged of corse and you will need to put the tool down the hole with the bend going over the switch cover when you have pushed the tool down the hole you need to lift the tool towards the unit handle as you do this it will push the clip out and as you do this you will need to wobble the switch cover it will come out but it may take some time its not easy so take your time gd luck
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i replace the power switch on a DC04? I can't get to the switch, are there any special tricks to open the swich module?

Yes there is a trick it you look at the switch cover at the edge nearest to the handle you will see a little groove down inside it is the clip that holds the cover on it iis part of the the switch cover and it is hard to remove without breaking it,yo ... Vacuums

I bought a Euro Pro Shark Steam Vaccum about 3 yrs ago. Now, suddenly, it won't switch on. I checked the power receptacle and tried other receptacles. It still won't switch on. I wanted to open and check the inside but it needs some special tools (and long screw drivers!). Any suggestions on what I could do?

... Euro-Pro S3325 Handheld Steam Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I have a raynor flight star garage opener. Had a lighting strike 4 days ago. All power is good. The opener even has a little green light on the switch that is attached to it. However the opener is not responding. Is there a way to reset on the motor by taking off the housing? I don't see any reset button on the out side of the housing.thnx w

You could always try unplugging the unit and plugging it back in. If that doesn't work the logic board is probably fried and unfortunately there is no replacement available for it any longer. You would need to buy a new opener. I'd recommend Liftm ... Vacuums

Got a Filter Queen Majestic Limited Edition, the one with the high and low power switch, an I have to change the power cord. How can I open the main unit to reach that power cord? Thanks,

First remove the top cap under your handle. \012Then, remove the three screws under the handle. \012remove the rubber cover on the switch\012undo the clamps on the side of the unit\012lift off the chrome cover with the cord on ... Filter Queen Majestic Canister Vacuum

I want to remove the power switch on a dc04 to repair a broken wore, how do i remove the switch?

Go to www.dysonmedic.com then scroll to the bottom of the page and click on DC04 cable change. You won't get better advice anywhere (and I've got no connection with dysonmedic). ... Vacuums


I am not an expert to this kind of machine but I can share with you this link below which I am sure would be a big help to you. Good luck. http://www.sparesaver.com/help-and-support/dyson-section/dyson-hints-and-tips-451/dyson-dc03-hints- ... Dyson Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

My wife's Viking 6690 smoked this last weekend. I opened up the end where the power switches are and the board had a 0.01 ufd capacitor the blew up. That would be easy enough to repair. However when the Cap blew, it also fried a small quarter watt resistor that sits just under the upper white pin connector on the board. The resistor is burnt beyond recognition and I am trying to find its value. Is there a schematic available for that board or a closeup picture of the board so that I could

According to you your machine's resistor burnt out. This resistor is located above the 240 volt capacitor which white base. change the resistor soon. For color code of the resistor you can follow the ... Vacuums

There is no power, how do i open it up to get to the cord end inside, and then maybe the switch.

To fishkeeper, I checked, it's kaput. So I gave up and went out and bought a Eureka Boss. MUCH better vacuum for a lot less money. I'm almost glad the Vax had a heart attack. ... Vacuums

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!

... Oreck Vacuums

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?

That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

Kirby G6 Power Switch Test ?

You can look at the wiring diagram and try to figure out how to use a circuit tester to test the switch but I would just suggest just swapping it for a good one (always good to have one good switch for testing) and see if it solves the problem. ... Kirby G6 Bagged Upright Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto

Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Dc04 does not power up!

I need a directional manual for dyson animal ... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity

... Vacuums

Eleectrolux canister sweeper power switch

There should be screws holding the handle asembly on to the top. One near the from, another by the handle, then slide the door near the back, there are 2 more screws there. with the handle off, you can get to the switch. Hopefully you can fina a r ... Electrolux Guardian Bagged Canister Vacuum

Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?

Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Can you send me a La Cimbali M22 Premium espresso machine power switch wiring diagram? I have a machine without a power switch. The switch is on order but I still have to connect the 10 loose wires. Thanks, Terry...

... Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0911 seconds