Having problems with your Vacuums ?
My Infinity Shark vacuum has lost suction. The pitch sound changes very soon after turning it on. I believe the lower hose is clogged, and I cannot get the body cove unattached where the hose bends upwards into the chamber.
So much for their claim of never losing suction!
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My Infinity Shark vacuum has lost suction. The pitch sound changes very soon after turning it on. I believe the lower hose is clogged, and I cannot get the body cove unattached where the hose bends upwards into the chamber. So much for their claim of never losing suction!
Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?
Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum
My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.
Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums
Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.
Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum
Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?
... Kenmore 25512/ 25513 Progressive Canister Vacuum
Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??
You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum
We cannot get the hose attachment to work. The
Try this guide.\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.
I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum
I HAVE EXTENDED THE WAND TO CLEAN MY STAIRS AND CANNOT GET IT TO GO BACK INTO THE HOSE.. IT IS AS IF I NEED TO CLICK A BUTTON TO ALLOW TO GO BACK IN BUT CANNOT FIND 1 ..IT IS NOW STUCK UP FULLY EXTENDED .. HELP ( YES IT IS NEW )
... Dyson DC27 Bagless Upright Vacuum
Cannot get hose to go back down.
Hi there SmartAlec from NelsonVacuums.com.au here. I think you will find that the hose will lock in easier if you remove the clear bin of the dyson. If it is not this then ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a Bissell 1694. I purchased a new pump and belt. The machine came apart very easy, but I cannot get it back together. The hoses don't all have a place to go or something
Don't know if this will help you out or not. it is for a different model, but the hose layout is about the same.\015\012\015\012 ... Bissell Vacuums
I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]
Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums
I have an electrolux renaissance c104a model vacuum...I got a sock stuck in the hose and took the end of the vacuum where it attaches to the canister apart. There are 4 brass pins that I cannot get back in the correct sequence to operate the vacuum...please help.
... Electrolux Guardian Bagged Canister Vacuum
Cord will not rewind: spring is unwound and cannot figure out how to retention it and then get body back together.
Try the link belowhttp://www.searspartsdirect.com/partsdir ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.
... LG Vacuums
I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.
Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums
Vacuum does not pick up dirt because hose is clogged and particles cannot get through to bucket
This is the order of what you should do to find out whether your vacuum has a clog in it:\015\012\015\012Start by checking the brush head of the vacuum to see if anything is stuck at the very beginning, and, if so, remove t ... Vacuums
The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.
... Dyson DC07 Bagless Upright Cyclonic Vacuum
I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.
Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums
I have cleared the vacuum hose and the attached motor unit. I cannot get the brush going. What else can I do? I have also checked the connections.
Make sure that the belt is on the unit properly not twisted or broken. Also make sure that the brush is set into place correctly and not rubbing on anything else. If both check out fine then the motor is not spinning for some reason and you will need ... Vacuums
I want to buy the removable tool rack with all parts but cannot find the hose anywhere. Is there a way I can get these items still?
... Hoover U5134-900 Bagged Upright Vacuum
I have a Dyson DC17 and I cannot get the detachable hose to pull up to use. I have tried pulling it up but it does not move and I can not use my detachable pieces. Is there a button I need to press - How do I fix?
Yes there is a button to release it near the handle i think , \015\012\015\012hope this helps ... Vacuums
What color is the air flow indicator supposed to be? Mine is yellow but I have no suction. I have read that some people have red, others yellow. I have cleared out all hoses and cleaned the filters with a shop vac, still cannot get it to pick up. Just keeps blowing the dirt out the back at me :(
Hi there, the unit may be experiencing something other than a blockage. Perhaps the dirt canister is not put back into place properly and the unit is sucking through there instead of through the hose.Check to see if the lid and the canist ... Hoover Elite Rewind Bagless Upright VacuumVacuum
Took the aromapro apart and cannot get the body to fit because of the flow control
Please contact our UK office at this link http://uk.bissell.com/Contact_Us.aspx ... Vacuums
My vacuum body does not fit on the water basin. There is a space where I cannot hook the clips. Is there a proper order to get the basin connected to the main machine?
... Rainbow Vacuums