Having problems with your Vacuums ?

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


Answers :

You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman


\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?


The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

My vacuum is obnoxiously loud all the sudden. the belt is fine and i can't figure out how to take it completly apart . any suggestions ???? .. [email protected]


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Eureka Capture Upright Vacuum Vacuum

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly


The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.


Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

Had to take bissell 8910 completely apart, need reassemble instructions


... Bissell ProHeat Pet Upright Deep Cleaner, Purple, 89104

Brush Hi I just bought a Kirby second hand. There is a small black rubber belt hanging off the brush. How can I take apart the bottom part of the vacume and where does this belt go to. Thanks Anita


Check out my step by step instructions...\015\012\015\012http://reviews.ebay.com/CHANGING-T ... Kirby G4 Bagged Upright Vacuum

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The brush is not spinning. I feel sucksion but the brush part is not spinning. I am hoping that I can take it apart but I do not have the manuel.


The belt needs replacing ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?


... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need a diagram to show me how to take the machine apart to fix the turbine


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.


Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum

Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John


Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a dc17 and there is a clog in it. I have taken the brush off, cleaned the hose, but there is something up inside the hose on the side that I can't get to. how to I take things apart so I can see to unclog it.


On the back of the vaccuum theres is a screw with a ubend hose...did you remove that? I have had things stuck in there which stopped suction? you may want to check that. also take the wand off and look through to make sure you can see light throug ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

Throughly cleaned roomba of dog hair, including taking off gears. After putting back together the brushes no longer move. Any suggestions


Try turning manually about 20 turns and re try, might have to do a couple of times, make sure no hair caught under yellow tips ... iRobot Roomba 560 Robotic Vacuum

The power head on my progressive vaccum doesn't seem to power on. Nothing appears to be stuck and not sure if I need to take it apart?? suggestions


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Light on tube leading to head of cleaner started flashing red and has now gone off completely (it's supposed to show red, amber, green according to level of soiling on carpet.) New bag has made no difference.Any suggestions?


Check for a clog in the hose or the dirt inlet by the brush roll. Also check your filters, if clogged, or black, replace them. ... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds