Having problems with your Vacuums ?

Electrolux renaissance how to change power headlight


Answers :

You will need to remove 5 recessed screws from the underside of the head, Then remove the cover and examine the bulb.
You may need to find an AERUS Electrolux service center for parts. Might as well clean out all the dust around the motor and remove and inspect the belt while you are in there.. Check the belt tension before loosening
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux renaissance how to change power headlight


You will need to remove 5 recessed screws from the underside of the head, Then remove the cover and examine the bulb. You may need to find an AERUS Electrolux service center for parts. Might as well clean out all the dust around the motor and ... Vacuums

Electrolux Renaissance power nozzle turning on and off, brass pins hot


The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the i ... Electrolux Guardian Bagged Canister Vacuum

My electrolux oxygen cannister has the "bag change" light on when there is a new bag. The light stays on when the suction power is high (to pick up small particles) and it won't pick up, but the ight goes off when the suction power is low (to pick up big objects). I changed the hepa filter, cleaned the motor filter and changed bags, but all that didn't help.


You may have a clog in the hose, and/or the inlet by the brush roll. A clog will turn on that light as well as a full bag. ... Vacuums

My vacuum does not suction floor debri the canister says change bag, i changed it 2 times with recommended electrolux bags. It will suctionwith wand and brush but not with power head


\015\012The power head has a separate motor to drive powerful carpet cleaning.Check if that motor is getting blocked or if its running slow/weak.Also check from any blockage in vacuum line.\015\012Keep updated with the results.\015\012Than ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Changing belt electrolux power nozzle PN 4 - Electrolux Vacuums


... Electrolux Vacuums

Electrolux renaissance bag is light and vacuum stops and the change bag light comes on


Mine is doing the same thing, well it was. I sat it upright and it seems to be working fine... there is no blockage in the hose, the bag is clean... only thing I can't change is the filter. Maybe that is the problem, it doesn't seem really dirty thou ... Electrolux Vacuums

How do i change the belt in my electrolux vacuum power nozzle


... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hello, My Electrolux Renaissance is about 12 years old. It worked great for years, but now it keeps turning itself off...about every 15 seconds or so. The bag was just changed recently, too. Is there an easy, (and cheap) fix or should I start shopping for a new one?? Thanks!


Odds are you have an obstruction somewhere. Check all of the hoses and the power head to ensure that there is nothing blocking your airflow. \015\012\015\012Also note that if it keeps popping the front bag door open, that's usually indica ... Electrolux Vacuums

Electrolux renaissance power hose


Call 5703261731 ... Electrolux Lux 7000 Bagged Canister Vacuum

Electrolux renaissance c104h will not start - no power lights go on


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

We understand that your problem is: I currently own and use on a regular basis the Kenmore Progressive upright bagged vacuum. Model number 116.35923500. The headlight flickers and the intelliclean light stays red. Ive tried cleaning the intelliclean sensors, changed the bag, and cleaned off the agitator. Is this a power issue? Should I take it to the store? Any suggestions would be greatly appreciated


Welcome to fixya\012\012Hello\012\012 \012\012I have a solution for this ... Kenmore Progressive 35922 Bagged Upright Vacuum

No power to panel on vacuum cleaner (electrolux oxy3 system)


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux Canister - Renaissance model


Probably a clog, because the change bag light is nothing but an airflow sensor. \015\012\015\012Check your hoses to ensure that there are no blockages, and also check inside the powerhead behind the brushroll. \015\012\015\012 ... Electrolux Lux 5500 Canister Vacuum

Electrolux Z8820 Ultraone.No sucking power and Sbag warning light is on


... Electrolux Vacuums

Electrolux ultraone not starting/no power


... Electrolux Lux 7000 Bagged Canister Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

I have an Electrolux Oxygen 3 vacuum I purchased rebuilt. After 1 month the power stopped working. I took it into Electrolux Authorized repair dealer, which was a horrible experience. When we received it back it was clearly not as powerful as before. Does anyone have any suggestions on what the problem may be? I would rather fix it myself than take it back to them. The next repair center is too far away. I am pretty good with fixing things, just needs some guidance. I think the repair center rep


Never have liked Electrolux doing any repair because it has been my experience that they don't do what they say they did....if you can read between the lines.....give me a picture of the unit and more details and I'll try and help you. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux genesis lxe won't power on


... Vacuums

Belt change on Electrolux Discovery M.1572E


... Electrolux Vacuums

Electrolux Renaissance canister


There are a couple situations to this issue. one is the bag that was replaced is a incorrect one and it is not meeting the switch for the bag pop circuit. some over the counter bags cause this issue. another problem could be the switch itself. or ... Electrolux Lux 5500 Canister Vacuum

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.


You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Was using my Miele Champagne vacuum, powered down, changed the bag, and now I have no power. I checked to make sure all lids were securely closed, still no power. Checked to make sure outlet was working, still no power...help.


Most likely the cord went bad, one side of it opened up, you will have to replace the cord reel asm. if this is the problem, Could also be a switch, electronic control or the motor. ... Miele Vacuums

I was vacuuming with the regular nozzle and all was well. Then I changed to the powered nozzle and the 2nd power level wouldn't work and then when I detached the powered nozzle I was unable to turn it ....there was no suction. The lights are on for low and high level but not middle level power.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?


Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

Chang the belt in my kenmore power mate power head


... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0434 seconds