Having problems with your Vacuums ?

How do I change the pump belt. I have the belt, but no instructions.


Answers :

What is the make and model of the cleaner?
I will need the make and model # for your????? Not really sure because you have it listed under vacuums but didn't include anything about it being a shampoo/carpet cleaner.

I'm going to take a guess here and say it is a carpet cleaner....possibly a Bissell. I'm right aren't I. (just lie to me and say good guess) ";-]

Ok if it is a Bissell then it's most likely a Proheat. Most Proheat models have two belts; a cogged belt that turns the brush\015\012roll, and a flat belt that turns the pump. The pump and belts are\015\012located in the front of the machine on the operator’s left. Turn the\015\012machine over and you’ll see a red retainer with 2 screws. Remove the\015\012retainer to gain access to the pump and belts. While you’re there check\015\012the red pump pulley, it’s where the two belts are.

If I'm incorrect and I am not the amazing Kreskin. Just respond back to me and I'll get it right. Right after you tell me.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change the pump belt. I have the belt, but no instructions.


What is the make and model of the cleaner? ... Vacuums

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

Pump Belt Replacement instructions


How do i change the belt? ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do you change belt on Bissell pro heat carpet cleaner. can you please send diagram or instruction how to change belts.


Http://www.bissell.com/images/UserGuides/7950_1204.indd.pdfhere is the complete manual (it is in pdf form)includes diagrams & instructions on belt replacment.thanx for using fix-ya!!!please rate all replys. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Product instructions need full view of internal schmatic and instructions on how to change belts or troubleshoot problems. I have the 1699 proheat and the 7901 Bissell I would appreciate a copy of operating instructions. Thank you, Raja Burns email address [email protected]


You can change the belts from the bottom, remove the brush roll, then you can reach thru slot to change the pump belt, then the cogged belt. Wasn't sure which darwing you wanted, if it is electrical, let me know.\015\012\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?


... Bissell Vacuums

Instructions to replace pump belt on model 37E3 bex bissell


... Bissell Vacuums

Eureka 437za belt change instructions


... Eureka Vacuums

Bissell 1697w I just got the bissell 1697 steamer and I had to replace the pump belt. I can not figure out how to change the belt.


First take off the belt cover on the side,\015\012then turn it over, on the belt end of the brush roll, there is a red piece to hold in the brush roll, take out that screw and pull it off, the you can remove the end cap and cogged belt, Put th ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

Want instruction on how to change the belt on electrolux velocity


N mine the roller it goes around has a 1/2 block set on each end held down by a spring (streight type) or 2 screws 1 on each side of the block. ... Vacuums

Lost instructions,need to change belt


The customer operation manual can be downloaded from the hoover web site hoover.com\015\012\015\012the bottom cover comes off with 4 screws. install the belt on the motor, then roller, stretch to install roller into cavity. replace cover. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How do i change belt for domotec hoover model dvu00001 lost instructions


... Vacuums

I need to change belt and cant find instructions


... Vacuums

I am trying to replace the pump belt on my Bissell Proheat 12 AMP moedel #7901-9. I was told this was the easy one to change, but it is only if you know where it goes and how to put it there. Can you give me some help? Pam


Here is a link to where you can view the manual. Hope it helps!Bissell ProHeat Belt and Manual ... Vacuums

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J


There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

Need instructions for how to change number 7 belts on bissell vacuum


Found the users manual online with directions for changing the belts. ... Bissell Vacuums

Instructions on changing a belt on an Elite Hoover Vacuum Cleaner Model # v5075-930 Serial # 089500053577


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=825812\015\012Generic problem for all Vacuums\015\012Instructions on changing a belt\015\012Posted by e ... Vacuums

How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I dont know how to change a shampoo pump on a bissell shampooer. Do you have instructions for me?


I need instructions how to change a shampoo pump on a 8910 bissel floor cleaner ... Bissell Vacuums

Nobody seems to be able to answer the question on how to change the belt on a bissell steam cleaner ..... Bissell is horrible for never giving customers proper instruction manuels .... THUMBS DOWN FOR BISSELL


I have the same prob. this is what i found\015\012\015\012\015\012Since changing the belt is the easiest fix, we suggest you check that first. (Before attempting any repair be sure your machine is unplugged from the electrical ou ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0686 seconds