Having problems with your Vacuums ?

We keep changing belt on tesco vcu007 but it breaks again as soon as we turn it on

Answers :

I am unfamiliar with this make and model, but assuming it is an upright vacuum cleaner type design, something must be stopping the brush/beater bar from rotating. When it is then switched on, this immeadiately places a huge strain on the belt which then snaps (quite often accompanied by a burning rubber smell)
\015\012If you still have the user manual, this should show you how to remove the bar, clean it and check for any foreign objects preventing the bar from turning. If not, beater bar removal isnt normally too difficult to work out.
\015\012Hope that helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We keep changing belt on tesco vcu007 but it breaks again as soon as we turn it on

I am unfamiliar with this make and model, but assuming it is an upright vacuum cleaner type design, something must be stopping the brush/beater bar from rotating. When it is then switched on, this immeadiately places a huge strain on the belt which ... Vacuums

Why does the belt keep breaking as soon as I turn on the vacuum?

Hi\015\012Have you got the correct belt? If its breaking then the brush end caps or something is clogged. If you can get into the floor head ensure you look at the actual brush roll to see if there is anything is clogged or trapped. Remove all matter ... Eureka 431A Optima Bagless Upright Vacuum

We have a dc04 and the belt keeps breaking as soon as we turn it on. Have u any ideas as we have took it apart and we think cleaned all parts

If the brush roller is sticky that will put a strain on the belt check it can turn freely and also the brush bearings are free ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt keeps breaking, but motor turns easily by hand on bissell powergroom, burnt rubber smell as well.....

Something is preventing the roller from spinning when in contact with the carpet. This causes the belt to stop turning and the motor shaft spinning in one spot causes the belt to burn and break. The protective guard could be damaged or not installed ... Bissell Powergroom Pet Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old

If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

Belts keep breaking

Check the brush roll ends to see if they have melted or frozen. They should turn freely, part #361869-1. Make sure the belt isn't being pinched somewhere. ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Dyson dc 14 the belt keeps breaking with the smell of burning rubber looks like the motor spindle does not turn any solutions

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissell 3522-5 belt breaks as soon as i install it and turn it on. Is a pulley supposed to be on the drive rod? If so, is there s replacement pulley available?

... Bissell 3522 PowerForce Bagged Upright Vacuum

I have tried 3 new belts and it breaks as soon as u turn the vacuum on.

The featherlight, and probably others by Dirt Devil are some of the worst designs I've ever encountered! The so called 'automatic' height adjustment consists of front wheels on a swivel mechanism that is forced up or down according to how high or low ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My vax essentials hoover, model number vec-01 keeps blowing fuse as soon as it is plugged in and turned on. Cleaned the filters and have changed the fuse 5 times

... Vacuums

My Kenmore Progressive keeps burning up belts even after I have changed the bag, cleaned the filters and checked to make sure the agitator was clean and free turning

On the left hand side, just above the handle release, is a lever to adjust if you are doing hard wood or carpet cleaning. When adjusted for hard wood, that lever releases the belt and just uses the "vacuum" function. When set for carpet it engages ... Kenmore Vacuums

Kenmore upright vacuum belt keeps breaking as soon as I put a new one on. I have made sure the brush roller is clean. How can I fix this or troubleshoot this?

... Kenmore 31723 Vacuum

The belt on my oreck xl keep breaking

The brush roller is siezing up on you.try to take the brush roller out and clean it real good .pull the ends off and clean them to things get caught up and wrapped around them and keep them from turning.before you put the new belt on clean the motor ... Oreck XL2200 Bagged Upright Vacuum

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.

... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Brush froze up and keeps breaking belts

I had the same problem but I found that I had replaced belt incorrectly. After placing one end of belt around pully, it has to be run behind the "belt disengager" which looks like a 1/2" wide metal tab just past pulley. After placing belt correctl ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My belt keeps breaking on my dirt devil classic ten amp vacuum 086600

... Dirt Devil Royal Plastic Brush Roll For Model 086600 Part 2620035600

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?

Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company. ... Hoover F6021-900 Steam Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther

Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I keep replacing the belt and keeps melting and breaks. what do i need to do? everything else is working, the little piece of metal that hooks on the belt gets too hot and melt the belt

I think your talking about the motor spindel,,(the little metal bit?) if the motor is that hot its going to burn out soon, check that the brush is free to turn if its tight free it off its full of grit or fluff also check that the motor turns freely ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1180 seconds