Having problems with your Vacuums ?

My elitech cyclone cleaner stair brushes will not rotate

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My elitech cyclone cleaner stair brushes will not rotate

... Vacuums

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for

Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate

If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin

Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

Got a Panasonic Eco max vacuum cleaner model mc-ul952.Brush bar does not rotate when switch set on ''carpet'.Brush bar clear....rotates freely by hand

... Vacuums

Windtunnel dual v vacuum cleaner brushes do not rotate when the vacuum cleaner is turned on

When you turn this model on, the only way to have the brushes turn is to move the brush control switch to on and then tilt the handle back. if all of this is ok but they do ot spin then check to see if you can turn them by hand with the machine off a ... Vacuums

Dc25 dyson upright vaccum cleaner. Brush inoperative. have changed on-off switch and the reset switch. the belt is intact and iam left with possible bad brush rotator motor???

... Dyson DC25 Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes

(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover steamvav, spinscrub carpet cleaner, brushes won't rotate or spin

... Hoover SteamVac Spinscrub 50 Carpet Cleaner

Lg luv3008 vacuum cleaner when I move the machine, the brush roller does not rotate

... LG Vacuums

I have a hoover carpet cleaner model # F7427-900 series Z120 and the rotating brushes stopped moving. How do I fix this?

The brushe until needs to be snapped in very hard; to line up correctly. Pull the unti off and put it back in, good luck. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes will not rotate on my steam vac - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I'm sorry to tell you that you have a broken drive brush. One of the brushes has a stem, and that stem is broken. See if you can remove the brush assembly - I believe it pulls straight down. See if one of the stems is a little longer than the othe ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

There is no cyclone action. The debris is filling the attachment hose. The brush bar is rotating but no debis is gathering in bagless cylinder.

Check your filter inside the dirt cup. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

We replace missing belt for roller brush on our bissell carpet cleaner, its loose and still doesn't rotate. Model # 8910 Looking for manual to fix this problem

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Spare drive belt for Elitech 2000W dual cyclone vacuum cleaner

... Vacuums

Cyclonic Upright Vacuum Cleaner mach 5 brush won't move

You need to replace the belt. Here is the belt you need: Hoover Mach 5 Cyclonic Upright Belt ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Kenmore Progressive Inteleclean Upright vacuum cleaner (with Bag) . It has good suction only through the hose now and none through the bottom for cleaning carpets. and, there is a noise like it has a suction leak. the brush is rotating.

Theres a little bendable neck that hose with suction plugs into. Thats the one thats clogged. You will have to fish it out by taking off the roller and clearing the clog. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks

Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0879 seconds