Having problems with your Vacuums ?

Brush won't turn, belts intact - Vacuums

Answers :

Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Brush won't turn, belts intact - Vacuums

Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Vacuums

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.

The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC07 brush does not turn - belt intact - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi there, The problem is likely to be \012a) The selector on the front of your machine is set to hard floors\012b) The ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?

There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!

Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover U5163-900 Brush turns freely but will not turn when the vacuum is on. Is it a belt and where is the belt??

Just discovered this same problem and the belt was a mess when we pulled it out. Now have to try to find a replacement and see if we can get it back on. To find it though just remove the 4 screws that hold the red cover on 2 on the bottom and then ... Hoover U5163-900 Upright Vacuum

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.

... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1522 seconds