Having problems with your Vacuums ?

Front rotor doesn't spin when the machine is first turned on


Answers :

You need to replace the belt. You can get replacement belts here:

Replacement Vacuum Belts
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Front rotor doesn't spin when the machine is first turned on


You need to replace the belt. You can get replacement belts here:Replacement Vacuum Belts ... Vacuums

My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?


The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums

Hoover FH50044 spin scrub. Brushes won't turn. All is clean. Brushes turn by hand when on the machine. Any help.


... Vacuums

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.


Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

The rotary brushes on my Windtunnel V2 won't spin. I wasn't having any problems just, boom, no more spinning. I've had to clean hair and other stuff from them in the past. At that time, they wanted to move and couldn't. Now, I turn the machine on, and they don't move but make a loud noise. What do I need to do?


... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Suction works but rotor wont spin. belt is new and connected. was vacuuming and it pulled a piece of clothing into the machine and I heard a snap or pop.


Try pressing the reset for the brushroll motor on the top of the brush head. also make sure the brush switch is engaged and stays in the on position. switches on these always go bad. start with the reset though thats probably what happened. If that d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have the ultimate g kirby. the green the brush doesnt spin when i turn it on and the belt is on correctly. whats the problem


You will find videos at this site that might be of help to you.\015\012\015\012http://www.kirby.com/Portals/0/videos.html\015\012\015\012If the brush does not spin you probably should remove it and clean well. Also, on each end of the br ... Kirby Ultimate G Bagged Upright Vacuum

My nostalgia cotton candy machine cart doesnt spin any more?


... Vacuums

I have a old janome sewing machine and looking to find out how to tread it.It doesnt have a model number on it. It has 2 dials and A to G stiching styles on the front. Made in Taiwan and number 656057510 on back approval number V/74088/750 It's only a straight sticher zig zag and button holder,very basic and maybe a type that they had in schools in 1970 in AUSTRALIA


... Vacuums

The spinner that shows that the suction or water is pumping out on the floor will not spin. I have checked the belts they are ok. I have turned it off for a few min. and it doesnt work.


The belts may look fine but they can be stretched or worn. If you haven't replaced them recently I would try that. You can get the belt you need here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance


The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA


It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.


The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes We have A Proheat Select X2. Brand new, using for the first time, heater works, liquid dispenser works, Power brushes on machine and on extension attachment do not turn. Any thoughts? Thanks gigi2244


If the floor brushes don't turn, there is a motor for that and it maybe bad, On the attchment, vacuum is what turns those brushes, On the tank there is a knob to turn for the floor or hose, is it turned for the right application? other then that, y ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The machine turns on and the indicator seems to be spinning but the water is not moving.


Operating the trigger does not dispense water into the spinning brushes - is that the problem?\015\012\015\012If so, remove the clean water tank and look in the opening behind the black grommet that seal the water tank. Operate the trigge ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0598 seconds