Having problems with your Vacuums ?

I am having trouble getting the wand extension to go all the way into the flexible tubing so that i can close off the top.

Answers :

Is it a dyson? make sure the top handle is snapped in properly and that will release the clip and allow the wand to go in
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am having trouble getting the wand extension to go all the way into the flexible tubing so that i can close off the top.

Is it a dyson? make sure the top handle is snapped in properly and that will release the clip and allow the wand to go in ... Vacuums

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.

... Euro-Pro Vacuums

I have a DC 15 Dyson Ball Vacuum. I've removed and cleaned the filter. I can't get the lid to close properly. I don't want to force it and break something. There is some kind of a red spring loaded tab that seems to be in the way. How do I reseal the top of the vacuum?

The red tab doesn't let the lid close if the filter is not fitted correctly or the wrong filter is fitted. Many after-market filters cause this problem. \015\012\015\012Have you recently fitted a new after-market filter? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.

Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 vacuumn system is stopped up, the clog is in the top part of the vacuum before it drops the dirt into the cylinder. Does the top part of the canister come off so that you can get into the tubes that are clogged.

... Dyson Vacuums

I have a 5 yr old Ariens snowblower ( model # 924124). I am having a problem with the deflector cable freezing. I had the deflector cable replaced a yr or 2 ago. I took the cable off and brought it in the house to thaw. When I reinstalled the cable, it worked ine except the shute does not operate in its full range of motion. I have the cable EXACTLY in its original position and routing. The shute only closes about half way. I cannot get the shute to close any lower. Any suggestions?

... Vacuums

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I cannot fit a Miele SF-AH 50 Active HEPA filter into my S524 Miele vacuum. It doesn't seem to have the rear tabs in the right place to push it into place all the way. When I put it into the place, the top won't close. I'm afraid I'll break something if I force it down. What is wrong?

... Miele S524 Mercury Bagged Canister Vacuum

Hi I have a hoover steamvac deluxe se. I am having trouble attaching the upholstery attachment to the front of the water tank. It gets stuck and I can't push it all the way down.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I cant get the tube out of the top of the sweeper

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty

There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

I have a Eureka bagless, The Boss, there is a clog behind the top dirt catcher. I have cleaned every other tube, filter, clogs, etc.. I can't get my hand up into the main housing. Thank you so much! Sijai

Try using a straightened wire coat-hanger. You should be able to bend a small hook at the end of the wire, and then bend it to get to the clog. If you can get the clog to move a little, but can't get it all the way out, try putting the vacuum back ... Vacuums

Where can i get a new flexible tube? - Beam Industries 2775 Serenity Plus Central System Vacuum

... Beam Industries 2775 Serenity Plus Central System Vacuum

My Dyson is clogged on top of the cyclones and I cannot find a way to open it up to get the clog out. Please help me. I have the purple upright Dyson. Thank you

Hi, Thankyou for using FixYa, We love to fix things.\015\012\015\012Hi your version of the Dyson is the Animal if its purple.\015\012\015\012Right, here we go.\015\012\015\0121. Firstly you have to detach the cyclo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell 1699 I have taken apart the pro heat cleaner. I reassemble it. The top cover will not go all the way down. Any suggestions on getting back together. Thank you

Make sure that the piston on the bottom of the smart mix valve is in the water only position.(needs be be on the knob and not sitting in the hole). With the top off, it is easier if you have a block of wood or something under the base to hold it up. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.

Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??

You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums

I have the dyson animal. There is something stuck in the wand tube and everyting is getting caught on it. There is very little suction from the wand. How do I get the wand apart or somehow get the object stuck out of the tube? Thanks

Yes, things stuck in vacuum hoses are not always as easy to remove as one might think. Trying to push it out with something can be counter-productive, and only get the thing stuck tighter! If you have a second vacuum, you can try sucking it out the w ... Vacuums

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it

My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Top o matic cigarette injector is only filling the cig half way

Hi Mindy, Make sure that your tobacco is not too wet. Set some tobacco out (about the amount you plan to roll) and let it air dry for about 5 - 15 minutes. You'll have to figure out how long to let it dry as your home temperature is different t ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins

Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.

... Elna Vacuums

Frozen top The top of my Shark sc505 is on so tight that I cannot get it off even with heavy duty tools. It appears to be frozen and will not move. How can I get it off so I can use it again?

I just bought one from a thrift store we were able to get the top off! We used wd 40 and vice grips and it came off. The machine looks like it was only used once and someone left the water in it. I immediately put white vinegar in it and rinsed it ou ... Euro-Pro Shark SC-505 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0497 seconds