Having problems with your Vacuums ?

When it gets warm it cuts out then when left for a

\015 My dyson upright vacum when it gets warm it cuts out then when left for a while will operate again is there a thermal cut out and if so how do you repair\015

Answers :

What model dyson is it? If its the DC17 check the rubber seal inside the canister at the bottom of the cyclone where the bottom door comes up. if you see a gap between that filter and the bottom lid then dirt has passed through your filters and went into the motor. This was a bad design for dyson and a common problem on the DC17 only. If that happened, the motor could be damaged. check for a clog somewhere in the vacuum, check both of your filters for dirtyness and cloggs.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When it gets warm it cuts out then when left for a


What model dyson is it? If its the DC17 check the rubber seal inside the canister at the bottom of the cyclone where the bottom door comes up. if you see a gap between that filter and the bottom lid then dirt has passed through your filters and went ... Vacuums

The problem has been getting worse. It works, then cuts off. Then works and cuts off. Making sure the canister is not full. Time b/w it working is getting longer and longer. Almost seems this time when I change the outlet it is plugged into it works. But then shuts off quicker than it was doing before. I'm getting very frustrated.


We had exactly the same problem with our Animal. After the motor was replaced under warranty a different engineer came out and diagnosed it as the cyclone chamber itself being clogged.(the bit with the purple cylinders on it). This is completely unse ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

There's a strip of pet hair that doesn't get picked up only on the left side of the roller, like it's rolling all of it up and kicking it out that side. I have to work from right to left to get it all up. is this a suction problem?


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Shuts off frequently The sweeper will run for a few minutes and when it starts to get warm it shuts off. If you allow it to cool off it will turn on again and run until it gets warm


Check any filters to see if they are clogged up with dust because its overheating the motor causing the thermal switch to trip. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The steam do not get hot it get warm athe water


Hi,Sarah, the unit is no good...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?


Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums

I have had my RCA microwave model # RMW1108 for about 8 months now. It was working fine until yesturday evening. I went to warm up some food for 2 minutes, the microwave itself was on and everything appeared to be working except my food did not get warmed up. I plugged it out and checked all over it for any damage but i could not find anything wrong. What would cause it to just stop heating up the food? Is this type of problem covered in the 1 year manufacturer's warranty.


... Vacuums

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA


It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My cord gets VERY warm when using my Dyson. Not HOT, but very very warm, warmer when closer to the electrical outlet. Should I be worried?


Hi Teresa, it's Jack at Dyson.I'm sorry to hear you're concerned about the power cord of your Dyson vacuum becoming warm in use. To confirm your machine is working correctly we'd like to take you through some quick troubleshooting checks over ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Scunci steamcanister model 52038 Steam does not get from canister through hose to nozzle. No apparent leaks - hose does not get warm. appears may be valve problem from canister to hose. Only used bottled water - barely used this machine.


... Scunci Vacuums

Cut out bit of smoke from left of machine motor


Return if still under warranty/ Could be motor... ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Machine cuts out due to getting hot


Most vacuums have a heat resister in when they overheat they cut out, this is normally because they are full up, got a blockage or the filters need cleaning, suggestions are, clean filters, empty and check for blockage. ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Filterqueen cuts out when warm


You should check the disc filter that is located under the paper cone support. The support is secured with a single screw in the middle at the bottom. This filter is commonly overlooked and when it gets dirty will restrict airflow and cause the motor ... Filter Queen Majestic Canister Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

The pre filter catch on my DC07 has snapped. I have the replacement, but can't get the bit left in the filter out! any ideas?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

My Shark steam mop S3202 is getting warm but not producing steam.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Shark steam mop power light goes on, basin feels like it is getting warm, but there is no steam or water released. Pad is completely dry. What's going on.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Today i was hoovering, and then my dyson just cut out! i left it a few hours then went back to it, it gave a little noise when i switched it on, then again i tried but it failed to come on! ive even changed the fuse in the plug! and now my dyson wont turn on at all, ive cleaned everything there is too clean! help! :D


It looks like you need a professional repair. If you're really lucky this may just be a break in the flex, or the switch has failed - both relatively cheap and simple to sort out. More likely, though, is a problem with the motor (carbon brushes worn ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off.


This post may be of assistance: http://www.fixya.com/support/t2842769-fix_new_power_cable_dyson_dc07\015\012\015\012Hope it helps ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Roller brush I took the roller off to clean it and now I can't get it back on without the left side just falling loosely to the floor.


Hi,\015\012\015\012you might need to order new floating roller bar holders, they were red on my bissell, they are held in place with two phillips screws on each end, I ended up using large washers to hold those on when my Bissell began m ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0402 seconds