Having problems with your Vacuums ?
Bissell pro heat
\015 How do i change the belt\015
The easiest way is remove the belt cover on the top housing, turn unit over, on the belt side remove the red plastic lock, one screw, then you can pull the brush roll cap out, take it off, then you can get to the cogged belt, look further in and you can get to the pump belt. You didn't which belt you want to change, if it is the cogged belt, check the end on=f the pump that the belt goes on, if the cogs are gone, you will have to replace the pump, if they are there, then just replace the belt and put back together.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bissell pro heat not spraying water - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Truction for bissell pro heat turbo 2x - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Bissell Pro Heat 8910 clogged?
Why the motor sounds muffled I am not sure. When the water is sucked up, it goes directly into the tank. The motor only creates the suction so it can do that. There should be a filter on the rim of the recovery tank lid, is it clean? Other then p ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a bissell pro heat water wont come out
The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have a bissell pro heat water wont come out
The pump may spin but the vanes inside could be broken or worn enough that they are unable to push water through the pump system. I am repairing a Bissell Model 8920 Pro-Heat 2X that has this very same problem.\015\012\015\012I tested all ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Replacement electric motor for Bissell Pro Heat 2x Select carpet
Bissell proheat i can spray solution from the handle but it has no suction help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell pro heat steam carpet cleaner, not releasing water.
That means that you need to replace the pump belt. Here is the belt you \012need and a manual you can view:\012\012Bissell 7901 Belt and ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell 2x pro-heat sprays water continuously.
... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Lost instruction book for my bissell pro heat turbo deep clean
BISSELL User’s Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Bissell Pro heat 2x the shampoo tank empties out
The o-ring is likely dislodged on the screw on cappersonally I would recommend just filling the soap container with water and a little bit of white vinegar instead of the detergent. You won't leave soap residue in your carpet that way. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissel power wash pro heat
Look under neath there is a **** hole. It may be plugged ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My pro bissell heat leaks.
The pop sound was an electrical component blowing inside the vacuum, probably one of the capacitors on the motor control board.Water is not leaking from the tank, water is getting released because the motor is not generating enough power ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell pro heat will not extract water from the carpet
Try checking the top section of the machine (where the dial is located to switch it from floor to tool) and there is a little red plastic piece about 1 inch square on the inside of it. This is a lint filter that has a little door on it. Open the do ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a Bissell pro heat water will not disperse from
If the red spray pieces are not clogged but the Bissell still will not dispense water, then I would say the next most likely causes of your issue was either no soap in the tank, or a burnt out water pump. But since you can get water through the tool ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I need instructions for bissell pro heat 2x cleaner
You can dawnload it from the manufacture,s website.you should go to there and dawnload it. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissel 1698 PowerSteamer Pro Heat Plus - Manual
This is the link for an Adobe file for the manual.\015\012\015\012http://www.bissell.com/images/UserGuides/1698.pdf ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
Bissell Pro Heat 2x steam cleaner, problems!
Must likely the brush motor is bad. The top cover has to come off to check it, this is where the tank sits on. Part # 2036757 and is #35 in the pix.\015\012\015\012 ... Vacuums
My Bissell Pro Heat 2X will not release water or
Its probably a solenoid that controls the flow to the floor, take it to a bissell repair center, because its not an easy fix. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
Bissel pro heat carpet shampooer 1699
Push the foot pad handle release on the left side lay the handle all the way back.Then lift the handle on the center bucket pull out and fill with hot tap water only no soap in the hole that fills up the plastic bladder.Flip the handle back down so t ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Bissell pro heat soap won't dispense
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell pro heat 2x multi surface carpet cleaner making spots
Maybe there's not enough vacuum or it hasn't been primed enough. I have a proheat that drove me crazy till I started leaving the heat switch on. I get wads of carpet fiber that mat around brush and spit out on the carpet, so I frequently remove them ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
How much soap and how much water do I put in the Bissell pro heat?
You are supposed to buy the Bissell soap. On the bottle depending which cleaner you need. The directions are on the bottle. Please do not use house hold cleaners because you can cause serious damage to the vacuum.\015\012Go here, this pg. shows ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell pro heat 2 puts out too much soap
... Bissell 8910 ProHeat Clear View Upright Vacuum
Brush not moving in Bissell pro-heat
If the belt is more then 6 months old or more, then the belt will have to be replaced reguardless of the way it lookes. belts can stretch over time and when you put the machine on the carpet the friction causes the brush to stop because the belt has ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum