Having problems with your Vacuums ?
I broke the handle of my vacuum mod. fm741b. How much cost replace it?
Unfortunately shark, euro pro doesnt sell any replacement parts. I just checked the schematics and the only things for that model available is belts, filters, light bulb and brushroll. I would look for a used one. in fact, let me look i might have a used one laying around. Email me if you want me to try and find you one.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I broke the handle of my vacuum mod. fm741b. How much cost replace it?
Unfortunately shark, euro pro doesnt sell any replacement parts. I just checked the schematics and the only things for that model available is belts, filters, light bulb and brushroll. I would look for a used one. in fact, let me look i might have a ... Vacuums
VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter
There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums
I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.
Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums
The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?
You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I believe I need to replace either the hose the handle or both, do you know how much they cost
It can cost a lot of money sometimes. But if it is really bad take it to a Vacuum Store they will fix it for you then they will tell you how much it is. ... McCulloch MC1275 Steam Vacuum
Ive a dyson DC05 in perfect working order, but the telescopic tube and the handle are broken, how much roughly should it cost to replace them? And does anywhere sell second hand parts?
Hi there SmartAlec from NelsonVacuums.com.au your post doesn't say where you are from but if you are in Australia then the rod is about $50 and the handle $20. If you are l ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]
You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
My Eureka Optima vacuum handle broke right at the metal tube.
I have exactly the same problem. I plan to drill a hole in the handle through plastic and metal, and then pass a metal pin to hold them together. I don't rotate the handle much, so the loss of handle spin functionality will not be a major issue for m ... Eureka 431A Optima Bagless Upright Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?
You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks
You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
My electrolux 2100 vacuum hose broke. I replaced the hose but now I dop not have power at the hose end. is there a curcuit breaker in the canister tha supplies power to the hose??
... Electrolux Guardian Bagged Canister Vacuum
How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930
... Hoover Vacuums
I had a house fire and lost most of my belongings. But I had just purchased a Shark Steam mop 3501. Loved it. Well it did not get destroyed in the fire but someone managed to break the handle off. Just the handle itself was broke off the rest of the handle rod is ok. I'm trying to see if I can replace the handle and not the whole shaft. Can you help me.
Yes you can replace jus the handle, the replacement part for the handle is available at the manufacturer's web site in the Parts and Accesories section. Enter M/N: S3501 to confirm it's the same as on your unit.\015\012\015\012 ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Handle broke handle of 2961avz somehow snapped in half. any ideas how to find a replacement handle?
Part # for the handle is 75765-3. You should be able to order thru a local service repair shop. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum
I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.
... Kirby Ultimate G Bagged Upright Vacuum
My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.
Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums
I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac
Need to replace lower handle and pivot as it broke off. I got replacement but no instructions how to replace.
Handle broke off when Vacuuming?
Two screws hold that handle onto the machine. Maybe they weren't installed when the machine was put together. \015\012If it broke part of the dust compartment, it's probably not worth fixing. \015\012If it broke part of the handle you can ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to
... Hoover U5344-900 WidePath Vacuum